Publicité
Les langues disponibles
Les langues disponibles
ALARM – Red Led:
o
fixed light means that the battery is off charge.
o
blinking light means that the battery voltage is becoming low.
o
if after charging the battery and having operated ON-OFF the main switch the red
light is still blinking, this requires the technical assistance provided in your territory.
IMPORTANT :
In the most part of the cases the speed 1 is enough to harvester olives, therefore we advise the usage of
this speed. In the rare event, instead, you need greater energy during the harvesting, it is possible to use
speed 2 for a limited period of time. The usage of speed 1 allow you to save both from the energy point
of view and also for the autonomy of the battery.
6.
USE OF THE BATTERY
Codes E1200L- E1200XL E4800L- E4800XL E4800L HD - E4800XL HD
The battery is not supplied with the machine . Please make reference to the user manual of the battery
and the battery charger to get indications on the usage precautions, maintenance and charging
instructions.
Codes E4800 BPL HD - E4800 BPXL HD
Olive harvester
E4800 BPL HD - E4800 BPXL HD
dedicated backpack and connected either to the power supply or to the battery charger alternatively
(never simultaneously).
The machine must be used only with the original battery, to be charged using only the original battery
charger. Battery life depends on the using conditions of the harvester.
In order to charge the battery, use the automatic charger 100÷240V AC, provided in the standard
equipment, connecting it to the socket and, later, to the battery connector. Connecting the electrical
outlet, two red LEDS turn on. Connecting now the battery, one of the 2 LEDs becomes orange.
The battery will be completely full only when the LED is green.
Charging time depends on the battery charge status. For the full charge, 5 hours are necessary. In case
of need, it is occasionally possible to charge the battery partially.
Charge the battery indoor, in a fresh, dry and aired environment.
Do not disassemble, drill, warm, wet, or modify the battery and the charger.
If the machine is not used for a long time, charge the battery completely, disconnect it from the machine
and store it. Recharge the battery every 3 months. If the battery is not charged for more than
3 months, it can be damaged and the warranty condition expires.
7.
TINES REPLACEMENT
Codes E1200L - E1200XL E4800L - E4800XL E4800L HD - E4800XL HD E4800BPL HD - E4800BPXL HD
Ref. fig. E (fig. E.1, E.2, E.3, E.4)
Identify the type of tine to be replaced using the drawing E.1.
Replace tines 2D/2S. 3D/3S and 4D/4S following the procedure described in fig. E.3:
With the 2,5mm wrench K (provided), unscrew the tine's locking nut D until the tine is free to come out
from its housing P and support Y. If the tine does not come out easily, use the tool S (included) and a
hammer to push it slowly out from its housing in the direction indicated by the arrow.
Fix the new tine in the support Y and then in the housing P, pushing it down eventually using a hammer.
Screw the locking nut up to the limit.
Replace tines 1D/1S following the procedure in fig. E.2 and fig. E.4: move manually the tines in the
position of maximum closure, as indicated by the 2 arrows in fig. E.2 and rotate the head on itself.
In this position, from the bottom hole F, use the 3mm wrench K (provided) to unscrew the tine's locking
nut until the tine is free to come out from its housing P and support Y. If the tine does not come out
ACTIVE S.r.l. - Via Delmoncello, 12 - 26037 San Giovanni in Croce - CR
Tel. 0375/94172
www.active-srl.com
are supplied with lithium battery inserted in a
email: info@active-srl.com
24
Publicité
