Publicité
Les langues disponibles
Les langues disponibles
*)
The specified values are emission values and do not
necessarily represent safe workplace values. Although
there is a correlation between emission and immission
levels, this cannot be used to infer whether additional safety
measures are necessary or not. Factors which affect the
current immission levels at the workplace, include the type of
room, other sources of noise, e. g. the number of machines
operating and other processes taking place in the vicinity.
Permitted workplace values can differ from country to country.
This information is designed to help the user to better assess
the dangers and risks.
**) The specified vibration emission value was measured in
accordance with a normed test procedure and can be used
in order to compare one electrical tool with another. The
specified vibration emission value can also be used for
an introductory evaluation of the exposure. The vibration
emission value may fluctuate from the specified value during
actual use of the power tool. These fluctuations will depend on
the way in which the power tool is used. Try to keep vibrations
to a minimum. One method of reducing the vibration load is,
for example, limiting the length of time you work with the tool.
All parts of the operating cycle must be taken into account for
this purpose (for example, also including times in which the
power tool is switched off and times in which it is switched on,
but is running without load).
ILLUSTRATIONS
DESCRIPTION (See figures)
P. 2, item A
1.
Tool
2.
Locking slider for tool
3.
On/off switch/stroke regulator
EQUIPMENT
•
Electric scraper
•
Scraper blade 1,5 mm
•
Scraper blade 3 mm
•
Operating instructions with safety instructions and
warranty
•
Suitcase
Note:
If any one of the parts is missing or damaged, contact
the retailer.
BRIEF DESCRIPTION
This scraper has been designed for tiles grout removal.
BEFORE USING THIS TOOL
Before using the tool, make sure the mains voltage is correct: it
must be the same as that on the specification label. Machines with
230V can also be connected to a 220V mains supply.
USING FOR THE FIRST TIME
SELECTING THE TOOL
You must select the tool according to the width of the tile grout
English
TRANSLATION OF ORIGINAL
you will remove.
Blades
Included:
Scraper blade 1,5 mm • 1/16" suitable for tile grouts from:
Scraper blade 3 mm • 1/8" suitable for tile grouts from:
Optional:
Scraper blade 2 mm • 3/32" suitable for tile grouts from:
Scraper blade 4 mm • 5/32" suitable for tile grouts from:
Tools can be sharpened. You must respect the tooth shape.
INSERTING THE TOOL
P. 2, item B
–
Slide the locking slider (2) into position
–
Slide the tool (1) as far as it will go into the tool holder (4).
–
Ensure that the tool is in the correct position (P. 2, item C).
–
Slide the locking slider (2) into position
STARTING THE TOOL
Operation
Check before switching on!
Check to make sure the device is in a safe operating condition:
–
Check to make sure there are no visible defects.
–
Check to make sure all device components are correctly
mounted.
Switching on and off
WARNING!
For safety reasons, the machine should always be
unplugged from the mains before inserting the tool.
CAUTION!
Risk of burning!
Shortly after being used, the tool may be very hot. Allow
a hot tool to cool down. Never clean a hot tool with
flammable liquids.
CAUTION!
Risk of cutting!
Even a tool which is at a standstill can still cut! Always
wear gloves when replacing the tool.
NOTICE!
Risk of damage to the unit!
The motor may overheat in the event of permanent
heavy loads and low revolutions. Run the motor at higher
revolutions in idle to allow it to cool down.
WARNING!
Check that the mains voltage is the same as that in the
machine's specifications.
Plug the machine in with the switch off.
11.
Publicité
