Publicité
Les langues disponibles
Les langues disponibles
546534
Sound and vibration levels in the specification are determined according to international standards.
The figures represent normal use for the tool in normal working conditions. A poorly maintained,
incorrectly assembled, or misused tool, may produce increased levels of noise and vibration .
www.osha.europa.eu provides information on sound and vibration levels in the workplace that
may be useful to domestic users who use tools for long periods of time .
Carefully read and understand this manual and any label attached to the tool before use . Keep these
instructions with the product for future reference . Ensure all persons who use this product are fully
acquainted with this manual.
Even when used as prescribed it is not possible to eliminate all residual risk factors . Use with
caution . If you are at all unsure of the correct and safe manner in which to use this tool, do not
attempt to use it .
General Power Tool Safety Warnings
WARNING: Read all safety warnings, instructions, illustrations and specifications
provided with this power tool. Failure to follow all instructions listed below may result in electric
shock, fire and/or serious injury.
Save all warnings and instructions for future reference.
The term "power tool" in the warnings refers to your mains-operated (corded) power tool or battery-
operated (cordless) power tool .
1) Work area safety
a) Keep work area clean and well lit. Cluttered or dark areas invite accidents .
b) Do not operate power tools in explosive atmospheres, such as in the presence of
flammable liquids, gases or dust. Power tools create sparks which may ignite the dust or
fumes .
c) Keep children and bystanders away while operating a power tool. Distractions can cause
you to lose control .
2) Electrical safety
a) Power tool plugs must match the outlet. Never modify the plug in any way. Do not use
any adapter plugs with earthed (grounded) power tools. Unmodified plugs and matching
outlets will reduce risk of electric shock .
b) Avoid body contact with earthed or grounded surfaces, such as pipes, radiators, ranges
and refrigerators. There is an increased risk of electric shock if your body is earthed or
grounded .
c) Do not expose power tools to rain or wet conditions. Water entering a power tool will
increase the risk of electric shock .
d) Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power
tool. Keep cord away from heat, oil, sharp edges or moving parts. Damaged or entangled
cords increase the risk of electric shock .
e) When operating a power tool outdoors, use an extension cord suitable for outdoor use.
Use of a cord suitable for outdoor use reduces the risk of electric shock .
f) If operating a power tool in a damp location is unavoidable, use a residual current device
(RCD) protected supply. Use of an RCD reduces the risk of electric shock .
3) Personal safety
a) Stay alert, watch what you are doing and use common sense when operating a power
tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol
or medication. A moment of inattention while operating power tools may result in serious
personal injury .
b) Use personal protective equipment. Always wear eye protection. Protective equipment
such as a dust mask, non-skid safety shoes, hard hat or hearing protection used for appropriate
conditions will reduce personal injuries .
c) Prevent unintentional starting. Ensure the switch is in the OFF-position before connecting
to power source and/or battery pack, picking up or carrying the tool. Carrying power
tools with your finger on the switch or energising power tools that have the switch ON invites
accidents .
d) Remove any adjusting key or wrench before turning the power tool ON. A wrench or a key
left attached to a rotating part of the power tool may result in personal injury .
e) Do not overreach. Keep proper footing and balance at all times. This enables better control
of the power tool in unexpected situations .
f) Dress properly. Do not wear loose clothing or jewellery. Keep your hair and clothing away
from moving parts. Loose clothes, jewellery or long hair can be caught in moving parts .
g) If devices are provided for the connection of dust extraction and collection facilities,
ensure these are connected and properly used. Use of dust collection can reduce dust-related
hazards .
h) Do not let familiarity gained from frequent use of tools allow you to become complacent
and ignore tool safety principles. A careless action can cause severe injury within a fraction of a
second .
4) Power tool use and care
DIY 1450W Sliding Mitre Saw
a) Do not force the power tool. Use the correct power tool for your application. The correct
power tool will do the job better and safer at the rate for which it was designed .
b) Do not use the power tool if the switch does not turn it ON and OFF. Any power tool that
cannot be controlled with the switch is dangerous and must be repaired .
c) Disconnect the plug from the power source and/or remove the battery pack, if detachable,
from the power tool before making any adjustments, changing accessories, or storing
power tools. Such preventive safety measures reduce the risk of starting the power tool
accidentally .
d) Store idle power tools out of the reach of children and do not allow persons unfamiliar
with the power tool or these instructions to operate the power tool. Power tools are
dangerous in the hands of untrained users .
e) Maintain power tools and accessories. Check for misalignment or binding of moving
parts, breakage of parts and any other condition that may affect the power tool's
operation. If damaged, have the power tool repaired before use. Many accidents are caused
by poorly maintained power tools .
f) Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges
are less likely to bind and are easier to control .
g) Use the power tool, accessories and tool bits, etc. in accordance with these instructions,
taking into account the working conditions and the work to be performed. Use of the
power tool for operations different from those intended could result in a hazardous situation .
h) Keep handles and grasping surfaces dry, clean and free from oil and grease. Slippery
handles and grasping surfaces do not allow for safe handling and control of the tool in
unexpected situations .
5)
a) Service Have your power tool serviced by a qualified repair person using only identical
replacement parts . This will ensure that the safety of the power tool is maintained .
Specific Safety
Mitre Saw Safety
WARNING: Before connecting a tool to a power source (mains switch power point
receptacle, outlet, etc.) be sure that the voltage supply is the same as that specified on the
rating label of the tool. A power source with a voltage greater than that specified for the tool can
result in serious injury to the user, and damage to the tool . If in doubt, do not plug in the tool . Using
a power source with a voltage less than the nameplate rating is harmful to the motor .
WARNING!
• Hold the power tool by insulated gripping surfaces only, when performing an operation
where the cutting tool may contact its own cord. Contact with a "live" wire will also make
exposed metal parts of the power tool "live" and could give the operator electric shock .
• Always use blades with correct size and shape (diamond versus round) of arbour holes.
Blades that do not match the mounting hardware of the saw will run eccentrically, causing loss
of control .
• Never use damaged or incorrect blade washers or bolt. The blade washers and bolt were
specially designed for your saw, for optimum performance and safety of operation .
• Keep hands away from cutting area and the blade.
IMPORTANT: If you are unsure about operating this tool after reading these instructions, please
seek additional training .
a) Do not allow anyone under the age of 18 years to operate this saw
b) When operating the saw, use safety equipment including safety goggles or shield, ear
protection, dust mask and protective clothing including safety gloves
c) Power tools may produce vibration. Vibration can cause disease . Gloves may help to maintain
good blood circulation in the fingers. Hand-held tools should not be used for long periods
without a break
d) Whenever possible, use a vacuum dust extraction system to control dust/waste
e) Do not attempt to cut material thicker than detailed in the Specifications section of this
manual
f) Mitre saws are not designed for general cutting of firewood. Always ensure wood is dry with
suitable flat surfaces, so it is securely held on the mitre table and fence
g) Only guide the saw blade against the workpiece when the tool is switched on. Otherwise
there is a risk of kickback when the blade becomes wedged in the workpiece
h) Adjust the cutting depth to the thickness of the workpiece
i) Never remove dust, chips or waste by hand close to the blade. Ensure the tool is unpowered
and use a suitable brush
j) Only use saw blades recommended by the manufacturer that conform to EN 847-1 or
equivalent standard in your country
k) Keep rags, cloths and string away from the work area and ensure the operator's clothing
has no loose strands of material that could become caught in the rotating blade, causing
injury. Gloves worn by the operator must not have loose strands
l) Ensure the mitre saw is operated without risk of items stored above falling onto the tool.
Vibration of the tool may cause nearby stored items to move
m) Keep saw blades not fitted to the tool in a suitable container to protect against cuts -
especially when carrying
silverlinetools.com
9
Publicité
