DWT AWS-20-115 D Notice Originale page 27

The area of the tool application can be expanded due
to use of additional accessories�
Power tool
components
1
Protective casing
2 Reducer
3 Spindle lock
4 Ventilation slots
5 On / off switch
6 Additional handle
7 Body
8 Filter
9 Battery lock *
10 Battery *
11 Mode switch
12 Indicator (state of battery charge / protection)
13 Indicator "MODE 2" (polishing / waxing)
14 Indicator "MODE 1" (grinding / cutting)
15 Charger *
16 Flange wrench *
17 Mounting lug
18 Screw
19 Spindle
20 Flange
21 Disc *
22 Clamping nut
23 Indicator (green) *
24 Indicator (red) *
25 Label *
* Optional extra
Not all of the accessories illustrated or described
are included as standard delivery.
Installation and regulation
of power tool elements
Before carrying out any works on the power tool
remove the battery 10.
Do not draw up the fastening elements
too tight to avoid damaging the thread.
Mounting / dismounting / setting-up of
some elements is the same for all power
tool models, in this case specific models
are not indicated in the illustration.
Additional handle (see fig. 1)
Always use the additional handle 6 when operating�
Additional handle 6 may be positioned as deemed
comfortable by the user�
• Unscrew additional handle 6 as shown on fig. 1.
• Screw additional handle 6 into another threaded
opening�
Protective casing
Always use protective casing 1 when ap-
plying cutting and grinding discs. Opera-
tion of the aforementioned accessories
without protective casing 1 is strictly
forbidden. Protective casing 1 should always face
the operator with its closed part.
Mounting / dismounting the protective casing (see
fig. 2)
• With a screwdriver (not supplied with the power tool)
release screw 18 and install protective casing 1 onto
the spindle neck, watching that mounting lug 17 comes
into the longitudinal groove of the spindle neck (see
fig. 2).
• Turn protective casing 1 into the required position
and tighten screw 18 with a screwdriver (not supplied
with the power tool)�
• When dismounting protective casing 1 repeat the
aforementioned operations in reverse order�
Mounting / replacement of accessories
After mounting accessories of any kind,
make a trial run before commencing op-
eration - start the power tool and let it
work in idle mode for not less than 30
seconds. The operation of accessories with radial
or axial run-out and causing increased vibration of
the power tool is strictly forbidden.
Wearing protective gloves is recom-
mended for mounting / replacing acces-
sories.
Mounting of cutting / grinding disc (see fig. 3)
• Install flange 20 onto spindle 19 (see fig. 3).
• Install one of the aforementioned accessories onto
spindle 19�
• Press and hold spindle lock 3�
• Screw clamping nut 22 onto spindle 19 and tight-
en it with flange wrench 16� Attention: at mounting
any accessories over 4 mm thick clamping nut 22
should be turned over (see fig. 3).
• Release spindle lock 3�
Replacing the cutting / grinding disc (see fig. 3-4)
• Press and hold spindle lock 3�
• Release clamping nut 22 with flange wrench 16 (see
fig. 4).
• Replace the accessory�
• Screw clamping nut 22 onto spindle 19 and tight-
en it with flange wrench 16� Attention: at mounting
any accessories over 4 mm thick clamping nut 22
should be turned over (see fig. 3).
• Release spindle lock 3�
of the power tool battery
Initial operating of the power tool
The power tool is supplied with a partially charged
battery 10. Before the first use, the battery 10 must
be fully charged.
Charging process (see fig. 5)
• Press the battery lock 9 and remove the battery 10
(see fig. 5.1).
• Connect the charger 15 to the power supply�
English
27
Charging procedure