Scheppach GS45 Traduction Des Instructions D'origine page 24

• Do not allow children to perform cleaning and main-
tenance tasks.
• Never operate the machine if other persons are in
the immediate vicinity.
• Keep your workplace in an orderly condition! Unti-
diness can result in accidents.
• Choose a working position alongside the equip-
ment or behind it. Never stand near the ejection
opening.
• Never reach into the filling or ejection opening.
• Keep your face and body away from the filling
opening.
• Do not overload the machine! You work better and
safer in the given performance range.
• Only operate the machine with complete and cor-
rectly attached safety equipment and do not al-
ter anything on the machine that could impair the
safety.
• Do not alter the motor controller setting, since the
rotary speed controls the safe maximum operating
speed, and protects the motor and all rotating parts
against damage due to excess speed. Contact the
customer service in case of problems.
• Do not operate without the funnel.
• Do not modify the device or parts of the device re-
spectively.
• Close machine properly before enabling motor.
• Do not hose down the device with water. (Origin of
danger electric current).
• Take into consideration environmental influences:
• Do not use the device in moist or wet ambience.
• Do not leave the machine standing in the rain or
use when raining.
• Provide for good illumination.
• To prevent danger of injury to fingers during assem-
bly or cleaning operations hold the cutting mecha-
nism (see pic. "Changing the blades") and wear
protecting gloves.
• If the cutting mechanism strikes any foreign object
or if the machine should start making any unusual
noise or vibration, immediately switch off and allow
the cutter to stop. Remove the plug from the mains
supply and take the following steps:
- Inspect for damage.
- Replace or repair any damaged parts.
- Check for and tighten any loose parts.
• Switch the machine off and remove the mains plug
from the socket when
- Performing maintenance and cleaning work.
- Eliminating faults.
- Check the machine for damage, if foreign ob-
jects have landed in the insertion channel
- abnormal machine vibrations
- Checking connecting lines, whether these are
knotted or damaged.
- Transporting.
- Carrying out repair work.
- Changing the blades.
- Leaving unattended (even during short interrup-
tions).
24 | GB
 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58
• If the machine's filling funnel or ejection slot is
blocked switch off the motor and disconnect the
mains plug before removing material from the filling
funnel or ejection slot.
• Check the machine for possible damage: Before
further use of the machine the safety devices must
be checked carefully for their proper and intended
function.
- Check whether movable parts function perfectly
and do not stick or whether parts are damaged.
All parts must be correctly installed and fulfil all
conditions to ensure perfect operation of the
machine.
- Damaged safety devices and parts must be
properly repaired or exchanged by a recognized,
specialist workshop; insofar as nothing else is
stated in the instructions for use.
- Damaged or illegible safety labels have to be
replaced.
• Store unused equipment in a dry, locked place out
of the reach of children.
• The permissible noise level is exceeded during
non-stop operation. We therefore recommend the
use of ear protection.
• Children under 16 may not operate the machine.
• Check mains cables. Do not use faulty cables.
• Watch for foreign objects during work. Do not insert
stones, glass or metal parts.
• Carry out repairs, maintenance and cleaning work
only when the drive unit is switched off. Wait until
the motor comes to a standstill and pull the mains
plug. Caution: The cutting tool continues to move
for some time!
• After finnishing work, do not switch off the motor
until the machine is completely empty, as it may
otherwise be difficult to start up again.
• Observe all safety instructions and warnings at-
tached to the machine. Cut off the external power
supply of the machine even if only minor changes
of place are envisaged. Properly reconnect the ma-
chine to the supply mains before recommissioning.
• When starting to work with the machine again, fol-
low the Operating Instructions.
• Use the machine in the recommended position and
on firm, even surface.
• Don't use the machine on a pavement surface with
grit strewed, on which thrown out material could
cause injury. Be aware of the cable, risk of stum-
bling.
• When transporting the machine, walk carefully; do
not run.
• Never pick up or carry the machine while the motor
is running.
• Don't bring hands, other parts of the body and
clothes into the infeed funnel, outfeed channel or
near to other moving parts.
• When starting up the machine stay always outside
the outfeed zone.
• Switch off the motor as soon as you leave work-
place.
• Don't tilt the machine with running motor.