Franklin Electric Little Giant LVL-PW Mode D'emploi

Franklin Electric Co., Inc.
Oklahoma City, OK 73127
www.lg-outdoor.com
customerservice@lgpc.com
INTRODUCTION
EN
This instruction sheet provides you with the information required to
safely own and operate your product. Retain these instructions for future
reference.
The product you have purchased is of the highest quality workmanship
and material, and has been engineered to give you long and reliable
service. This product has been carefully tested, inspected, and packaged
to ensure safe delivery and operation. Please examine your item(s)
carefully to ensure that no damage occurred during shipment. If damage
has occurred, please contact the place of purchase. They will assist you
in replacement or repair, if required.
READ THESE INSTRUCTIONS CAREFULLY BEFORE ATTEMPTING
TO INSTALL, OPERATE, OR SERVICE YOUR PRODUCT. KNOW
THE PRODUCT'S APPLICATION, LIMITATIONS, AND POTENTIAL
HAZARDS. PROTECT YOURSELF AND OTHERS BY OBSERVING
ALL SAFETY INFORMATION. FAILURE TO COMPLY WITH THESE
INSTRUCTIONS COULD RESULT IN PERSONAL INJURY AND/OR
PROPERTY DAMAGE!
SAFETY GUIDELINES
DISCONNECT THE UNIT FROM POWER BEFORE SERVICING OR
REMOVING ANY COMPONENT!
Choose a location for both safe and easy installation and avoid areas with
chemicals, explosives or other dangerous materials.
Do not handle light with wet hands or when standing on a wet or damp
surface, or in water.
If the power cord fails for any reason, please contact an authorized service
center or the manufacturer.
ELECTRICAL CONNECTIONS
1. The lights are rated 20W, 12VAC. DO NOT connect to voltage other
than stated voltage.
2. Connect fixture to suitable 12V transformer. In Canada, the luminaire
shall be connected/supplied from a CSA Certified Class II supply with
double insulated transformer or transformer with grounded shield
between primary and secondary winding of the transformer.
PW and LVT-PW meet these requirements.
1. Lights are designed to used completely submerged.
2. To connect the lights, refer to the instructions included with your
transformer.
3. Always carry the light by its housing and not by its connection cable.
4. Select a location for both safe and easy installation and avoid areas
with chemicals, explosives or other dangerous materials.
5. Select the appropriate mounting bracket. The small pipe bracket can
be used on any pipe with an approximate O.D. of .84". The large pipe
bracket can be used on any pipe with an approximate O.D. of 1.32".
Install bracket as shown in the illustration.
6. If instability occurs due to the light buoyancy, rocks or bricks may
need to be placed around or on top of the pump to provide additional
support.
LVL-PW
LVLT-PW
Light Kit • Kit Électrique •
Juego de Luz
OPERATION
7. To install colored lens, press the desired lens into the front of the
outer ring as shown in the illustration and rotate the lens clockwise
until it is snug. NOTE: The colored lens can only be installed with the
beveled edge facing away from the light (Figure 1). Do not remove the
clear glass lens.
8. DO NOT let the unit freeze. This may cause cracking or distortion that
may destroy the unit or cause safety problems.
DISCONNECT THE UNIT FROM POWER BEFORE SERVICING OR
REMOVING ANY COMPONENT!
CAUTION: Do not remove cord strain relief (hex nut). This will damage
seal and result in possible leakage.
NOTE: No tools are required to service light.
1. LAMP REPLACEMENT:
a. Unscrew the outer ring by turning it counterclockwise, then remove
the glass lens and o-ring.
b. Remove the lamp. CAUTION: The lamp and reflector are one
piece. DO NOT pull on the lamp itself; pull only on the reflector.
c. Insert new lamp into socket as shown in Figure 1. DO NOT touch
the lamp; only touch the reflector. Touching the lamp may shorten
its life.
d. Make sure o-ring is in good shape and clean, then reinstall o-ring
and lens.
e. Reinstall the outer ring. DO NOT use any tools. Tighten the outer
ring until tab on light ring touches mounting rib on lamp housing.
CAUTION: MAKE CERTAIN NO WATER OR MOISTURE IS INSIDE
LAMP PRIOR TO THE REASSEMBLING.
2. CLEANING: Periodically wipe off the outside of the lens with a soft
cloth. DO NOT use abrasives as this may damage lens. CAUTION:
If lamp is disassembled for cleaning, be certain lamp housing is not
submerged in water. This will allow water to enter cord which could
result in an electrical hazard.
Cette feuille d'instructions vous fournit les informations nécessaires pour
entretenir et faire fonctionner votre produit. Conserver ces directives afin
de pouvoir les consulter plus tard.
Le produit que vous avez acheté a été soigneusement fabriqué avec des
matériaux de la plus haute qualité et a été conçu pour durer longtemps et
offrir un service fiable. Les produits sont soigneusement testés, inspectés
et emballés afin d'en assurer la sécurité de fonctionnement et une livraison
en bonne condition. Vérifier attentivement le produit afin de vous assurer
qu'il n'a pas été endommagé pendant le transport. S'il est endommagé,
veuillez contacter l'entreprise qui vous l'a vendu. Si une réparation ou un
remplacement est requis, elle vous prêtera assistance.
LIRE ATTENTIVEMENT CES DIRECTIVES AVANT DE PROCÉDER À
L'INSTALLATION, À L'UTILISATION OU À L'ENTRETIEN DU PRODUIT.
The LVLT-
SE FAMILIARISER AVEC LES APPLICATIONS, LES LIMITES ET
LES RISQUES POTENTIELS DU PRODUIT. ASSURER SA PROPRE
PROTECTION ET CELLE DES AUTRES EN SUIVANT TOUTES LES
RÈGLES DE SÉCURITÉ. LE NON-RESPECT DE CES DIRECTIVES PEUT
ENTRAÎNER DES BLESSURES ET/OU DES DOMMAGES MATÉRIELS!
VEILLER À
D'ALIMENTATION
TRAVAUX D'ENTRETIEN OU LA DÉPOSE DE L'UNE DES PlÈCES!
Choisir un emplacement où l'installation pourra être faite facilement et en
toute sécurité. Éviter la proximité de produits chimiques ou explosifs, ou
d'autres matières dangereuses.
Ne pas manipuler la lampe avec des mains mouillées, les pieds posés sur
une surface humide ou mouillée ou dans l'eau.
Si le cordon d'alimentation ne fonctionne pas correctement ou est rompu,
communiquez avec un centre de autorisé service ou le fabricant.
1
SERVICE INSTRUCTIONS
INTRODUCTION
FR
WARNING
AVERTISSEMENT
DIRECTIVES DE SÉCURITÉ
AVERTISSEMENT
DÉBRANCHER L'APPAREIL
ÉLECTRIQUE AVANT
DE SA SOURCE
D'EFFECTUER DES