Conrad PROFIPOWER Mode D'emploi page 6

1 Indications for using the manual
ATTEnTIOn:
Safety reference: Not concerning may lead to material damage and may
influence or harm the functioning of the device
ATTEnTIOn:
Safety reference: Refers to the dangers concerning electric flux or vol-
tage. Neglecting these references may lead to personal damage and/or
material damage. Also may the functioning of the device be influenced/
harmed.
REMARK:
Additional information with regard to controling the device
Image number/number refers to an image.
e.g. image 1/4: image 1 on page 4
Consider the next safety references.
2 General Safety References
The company axhess GmbH & Co. KG, 53457 Hausen, takes no respon-
sibility for damages and consequences which arise due to:
- Connecting, mounting or control failures
- Outrage, damages to the device and/or the connecting cables.
- Equipment damages due to mechanical influences and/or over-vol-
tage.
- Any changes inflicted to the device and/or the connecting cables.
- Use for all other purposes as described in this manual.
- Liquid influences and/or insufficient ventilation.
- Opening the device unauthorized; this will, among others, lead to the
lost of the given warranty.
- Consequential damage caused by non-intended use and/or a defec-
tive battery.
Handle this device exclusively for its intended use.
Never use in a moisty or wet environment!
Use the device exclusively in a dry environment!
Never handle this device close to inflammable material.
Never handle this device in an explosive hazard environment.
Exclusively use the device when there are sufficient possibilities for ven-
tilation.
Repairs and maintenance may only be accomplished by authorized
specialists, who are familiar with the dangers/regulations which go along
with this equipment.
Always make sure the equipment is in a safe, solid condition!
Mount the time switch in such a secure way it surely doesn't collapses
or falls down.
The equipment is such a secure way children do not have access to it!
Children do not recognise originating dangers, neither are they able to
estimate them!
12
profipower_2440007_Timer2_Manual_1292_ok_k1.indd 12-13
Do not directly expose the equipment to sunlicht or other sources of
heat. Avoid additional heating of the device by outside influences.
To avoid damages to the connecting cables: never pull the cable but
always disconnect by using the plug.
If the connecting cable is damaged the device may not be used any lon-
ger! First, the device needs to be repaired by an authorized specialist.
Do not place any inflammable objects like candles on or close to the
device.
No objects filled with liquid, like bottles or drinking cans, may be placed
next to, on, or close to the device.
3 Way of supply
1 x 12 V time switch
1 x Button cell 3 V
1 x Multilingual manual
1 x Recyclable packaging
4 Intended use
Time switches, and therefor also this 12 V version, are developed to automa-
tically switch on connected devices on a pre-determined moment. Also, the
time switch switches off again a connected device, as well on a pre-deter-
mined moment.
There is one condition for doing so; the time switch needs to be connected to
a 12V rated current socket. Settings of the time switch are being recorded. A
supporting battery (exchangeable) inside the time switch makes sure all data
is being saved when the time switch doesn't receive any 12 V voltage from the
car battery. Set data is being conserved.
This time switch is developed for the use in combination with 12 V vehicle
batteries. Other voltages will disturb the 12 V time switch, do not connect to
any other voltage!
The maximal output is 10 A. Connecting devices with a power consumption
from 12 V/10 A up to 120 W at the upmost can be used with this time switch.
ATTEnTIOn!
Before you set the 12 V time switch in operation check, by using the tuto-
rial of your vehicle, the current supply and the maximal load of the 12 V
board contact (cigarette lighter) of the vehicle.
ATTEnTIOn!
Always consider the following basic precautions for your own and others
protection to avoid:
• electrical flashes
• risk of fire
• injuries
• material damage
Only start using the device when the housing and cabling are completely
intact!
13
25.08.2009 11:25:55