Publicité
Les langues disponibles
Les langues disponibles
Setting Up Your Vicks Warm Mist Humidifier
1.
Remove packaging materials. Keep this Instruction Manual for reference.
2.
Remove twist tie from power cord and extend power cord full length.
3.
Ensure Proper Assembly. Make sure Mist Chimney, Medicine Cup,
and Water Tray are securely in place and that Heating Element Cover
is secured. See Reassembling instructions for reference.
4.
Place humidifier on a firm, level, water resistant surface a minimum
of 12 inches (30 cm) from walls. Steam should be directed away
from any walls, bedding, or furniture.
WARNING : KEEP OUT OF REACH OF CHILDREN. THIS PRODUCT PRODUCES HOT
STEAM AND SHOULD BE PLACED IN AN AREA NOT ACCESSIBLE TO CHILDREN OR
PETS, WITH THE POWER CORD OUT OF REACH.
Filling / Refilling
NOTE: WATER TANK SHOULD BE CARRIED USING TWO HANDS; ONE HAND ON THE TANK HANDLE
AND THE OTHER SUPPORTING THE BOTTOM OF THE TANK.
Kaz USA, Inc. will not accept responsibility for property damage caused by water spillage.
Step 1
Step 2
1.
Remove Water Tank by grasping Handle and pulling up. Remove Tank Cap by turning counter
clockwise. (to left)
2.
Fill Tank with cool water. DO NOT fill with warm or hot water.
DO NOT ADD ESSENTIAL OILS, MEDICATIONS, OR INHALANT LIQUIDS such as Vicks
VapoSteam
®
or Kaz Inhalant to the Water Tank. Doing so could cause damage to the humidifier
and void the warranty.
3.
Replace Tank Cap by turning clockwise (to right) to screw back in place. DO NOT over-tighten.
Place Tank back on humidifier Base.
Resetting When Reset Light Illuminates
When your humidifier is out of water, the Reset Light will illuminate. To reset:
1.
Turn power OFF (
)
2.
Refill and replace Water Tank.
3.
Wait 5 minutes and turn power ON (
Note: If Reset Light (
) is still on, clean Heating Element (see cleaning instructions)
4
Step 4
Step 3
Reset Light
)
Using Your Humidifier
Step 1
1.
Power: With the Power Knob in the OFF position ( ), plug the filled humidifier into a polarized
120V outlet.
CAUTION: To avoid electric shock, DO NOT plug in humidifier with wet hands.
2.
Output: Turn Power Knob to high (
is working, but it will take 3-4 minutes for visible steam to appear.
3.
Humidity Level: Once a comfortable humidity level has been reached, turn to the low setting.
A comfortable humidity level is between 40-60%.
Consider using a humidity monitor such as the Vicks V70 Humidity Monitor to display current
room humidity and temperature. If condensation forms on walls, windows, or around unit, turn
humidifier off; the humidity level is too high.
CAUTION: TURN HUMIDIFIER OFF, UNPLUG AND WAIT 20-30 MINUTES FOR
UNIT TO COOL BEFORE MOVING OR CLEANING. DO NOT OPERATE YOUR HUMIDIFIER
WITHOUT THE TANK IN PLACE OR IF THE UNIT IS EMPTY. DO NOT OPERATE YOUR
HUMIDIFIER WITHOUT THE MIST CHIMNEY, WATER TRAY, HEATING ELEMENT
COVER, OR MEDICINE CUP PROPERLY ASSEMBLED.
Using Liquid Inhalant
Liquid Inhalant
®
Liquid Inhalants such as Vicks VapoSteam
ONLY USE LIQUIDS THAT ARE RECOMMENDED FOR THIS TYPE OF HUMIDIFIER.
1.
Add 1 Tablespoon of inhalant to the Medicine Cup. ONLY pour inhalant into Medicine Cup.
DO NOT pour into Mist Chimney. DO NOT ADD LIQUID INHALANTS, ESSENTIAL OILS, OR
ANY ADDITIVES TO THE WATER. DOING SO CAN HAVE ADVERSE EFFECTS ON THE
HUMIDIFIER AND VOID THE WARRANTY.
2.
Note: Some residue from inhalant may be left in Medicine Cup after use. To clean, ensure
the humidifier is off, unplugged, and cooled for at least 20 minutes and gently wipe residue
from Medicine Cup.
The Medicine Cup can also be used with essential oils. Add a few drops to the medicine cup
for added enjoyment. NEVER add to the Water Tank or Reservoir.
Step 2
Step 3
) or low ( ). A green light will indicate the humidifier
Step 1
1 Tbsp
or Kaz Inhalant can be used in the Medicine Cup.
®
Step 2
5
Publicité
