HeatStar HS50KPA Guide D'utilisation Et Instructions De Fonctionnement page 4

NEVER LEAVE THE HEATER UNATTENDED WHILE BURNING! NEVER LEAVE THE HEATER UNATTENDED WHILE BURNING! NEVER LEAVE THE HEATER UNATTENDED WHILE BURNING!
3.­ Slide­the­large­washer,­then­wheel­onto­the­axle­next­to­the­
cotter­pin.
4.­ Slide­the­spacer­onto­the­axle­next­to­the­wheel.
5.­ Slide­the­partially­assembled­axle­through­the­wheel­support­
frame.
6.­ Slide­the­spacer­onto­the­axle­next­to­the­wheel­support.
7.­ Slide­the­wheel,­then­large­washer­onto­the­axle­and­hold­in­
place­with­the­remaining­cotter­pin.
8.­ Install­the­caps­over­the­larger­washers­to­finish­the­wheel­
assembly.
EXTENSION GUARD ASSEMBLY (FOR UNITS SOLD IN
CANADA)
Tools:
a.­Standard­Flat­Bladed­Screwdriver
b.­5/16­open­end­wrench
HS50KPA, HS80KTPA
1.­­ Remove­the­two­(2)­heater­exhaust­end­screws­from­the­top­
shell.
2.­­ Place­guard­onto­the­exhaust­end­lip­of­upper­shell­with­the­
extension­of­he­guard­way­from­heater.
3.­­ Align­the­mounting­holes­with­the­holes­in­the­shell­from­
step­1­above.
4.­ Using­the­two­(2)­screws­included­in­the­screw­pack­attach­
the­guard­to­the­heater,­and­tighten.
HS140KTPA, HS185KTPA, HS210KTPA
1.­­ Place­the­guard­onto­the­top­of­he­exhaust­handle.­The­
guard­extension­will­be­parallel­with­the­ground­and­going­
way­from­the­heater­exhaust.
2.­­ Align­the­four­(4)­mounting­holes­in­the­exhaust­handle­with­
those­in­the­guard.
3.­­ Using­four­(4)­screws­and­four­(4)­nuts­found­in­the­
hardware­pack,­attach­the­guard­to­the­exhaust­handle­and­
tighten.
WARNING:­Guards­are­NOT­handles.­DO­NOT­use­the­guards­
to­move­or­handle­the­heater.
PREPARING FOR OPERATION
1.­ Check­the­heater­for­possible­shipping­damage.­If­any­is­
found,­immediately­contact­the­manufacturer­at­
866-447-2194.
2.­ Follow­all­of­the­"Precautions".­
3.­ Fill­the­fuel­tank­with­clean­kerosene.­In­extremely­cold­
weather,­condensation­may­develop­in­the­tank­and­it­is­
recommended­that­a­tablespoon­of­de-icer­be­added­for­
each­gallon­(3.78­Liters)­of­fuel­in­the­tank.­When­filling­the­
heater,­use­at­least­2­gallons­(7.57­liters)­of­fuel.­Be­sure­
heater­is­level­and­do­not­overfill.­Use­a­funnel­or­can­with­a­
long­fill­spout.
IMPORTANT: Before filling fuel tank the first time or after ex-
tended storage periods, drain the fuel tank of any moisture
or condensation.
4.­ Locate­heater­at­a­safe­distance­from­combustible­materials.­
Models­HS50KPA­&­HS80KTPA­are­not­suitable­for­use­on­
wood­floors­or­other­combustible­materials.­When­used,­the­
heater­should­rest­on­suitable­insulating­material­at­least­1­
inch­thick­and­extending­3­ft.­or­more­beyond­the­heater­in­
all­directions.
Heatstar, Inc. | Kerosene Forced Air Heater
HEATER START UP
1.­ HS50KPA:­Plug­the­heater­into­a­grounded­1 15V,­60­Hz,­
1­Ø­outlet.­Start­heater­by­pushing­toggle­switch­to­"On"­
position.
HS80KTPA, HS140KTPA, HS185KTPA, HS210KTPA: Turn­
thermostat­to­lowest­setting,­and­make­sure­"On/Off"­
switch­is­"Off".­Plug­the­heater­into­a­grounded­115V,­60­Hz,­
1­Ø­outlet.­Turn­thermostat­to­highest­setting.­Start­heater­
by­pushing­toggle­switch­to­"On"­position­(light­signifies­
switch­is­in­"ON"­position).­Adjust­thermostat­to­desired­
setting.­Heater­will­cycle­on/off­as­heat­is­required.
EXTENSION­CORD­REQUIREMENTS:­Up­to­100'­(30.5m)­use­
16­awg.­conductor.­101'­-­200'­(30.5­-­61.0m)­use­14­awg.­
conductor.
For all models:
•­ In­cold­weather­(below­10°­F),­starting­may­be­improved­by­
holding­a­finger­over­the­vent­hole­of­the­pump­adjustment­
screw­cap­until­the­heater­starts.­
•­ This­unit­is­equipped­with­an­interrupt­circuit.­The­reset­is­
integrated­into­the­"On/Off"­switch.­If­the­unit­does­not­
start,­toggle­the­switch­to­"Off",­wait­5­min.­and­toggle­
the­switch­to­"On".
HEATER SHUT DOWN
1.­ HS50KPA: Push­"On/Off"­switch­to­"Off"­position.­Unplug­
heater­from­power­source.
HS80KTPA, HS140KTPA, HS185KTPA, HS210KTPA: Push­
"On/Off"­switch­to­"Off"­position.­For­extended­shutdown,­
unplug­heater­from­power­source.
RESTART AFTER SAFETY SHUTDOWN
HS50KPA­-­Unplug­unit.­Wait­5­minutes.­Plug­back­in.
HS80KTPA,­HS140KTPA,­HS185KTPA­&­HS210KTPA­-­Toggle­switch­
to­"OFF"­position,­wait­5­minutes.­Restart.
MAINTENANCE AND STORAGE
WARNING:­To­prevent­personal­injury,­unplug­the­heater­from­
the­wall­outlet­before­servicing.­
For­maximum­efficiency­and­trouble-free­service,­make­the­
following­periodic­maintenance,­cleaning­and­inspections.
ADJUSTING PUMP PRESSURE
Due­to­varying­fuel­viscosities­and­normal­component­wear­the­
pump­pressure­on­this­heater­may­need­to­be­adjusted.
FUEL­PRESSURE­ADJUSTMENT­SCREW
­­­­­­­­­­­­­­­­­­­­­­­­­­(located­at­the­rear­of­the­heater)
4
Operating Instructions and Owner's Manual
PRESSURE­GAUGE