Publicité
Les langues disponibles
Les langues disponibles
■ FURTHER SAFETY INSTRUCTIONS
Read all instructions before using this product!
Work Area
To Avoid risk of personal injury, equipment
damage, fire and shock make sure your Work
Area is:
• Free of damp, wet or rainy conditions
• Free of flammable gasses or liquids
• Childproof – use padiocks and master swit-
ches when not in use
• Clean and uncluttered
• Well ventilated and well lit
The machine corresponds with the valid EC
guideline.
• Before starting work, all guards and safety
devices must be fitted to the machine.
• The machine has been designed to be
operated by one person. Within the working
area, the operator is responsible with regard
to third persons.
• All safety and danger warnings attached to
the machine must be observed.
• All safety and danger warnings attached to
the machine must be kept in complete and
legible condition.
• With the tools and accessories offered, the
machine has been conceived for steel and
nonferrous metals only.
• The machine has been built using modern
technology in accordance with recognized
safety rules. Some hazards, however, may
still exist.
• Injuries on fingers and hands caused by the
running tool in case of incorrect guiding of
the work piece.
• Health hazards through steel chips. It is
imperative to wear personal protective gear
like goggles.
• Injuries through defective cutting off wheel.
Prepare the workplace where you intend
to place the electrical power tool. Provide
1.
Machine head
2.
Thermal circuit breaker
3.
On/off switch
4.
Handle
5.
Guard, fixed
• Know the machine. Learn its applications
and limitations, as well as the specific
potential hazards.
• Check for damage if part of the machine is
The Operator
Common sense and caution are Factors which
cannot be built into any Product. These factors
must be supplied by the Operator. Please
Remember:
Prevent body contact with grounded surfaces
such as pipes or radiators.
Stay alert. Never operate equipment if you are
tired.
Do not operate the product of under the influ-
ence of alcohol or drugs. Read warning labels
on prescriptions to determine if your judge-
ment / reflexes might be impaired.
Do not wear loose clothing or jewelry as they
can be caught in moving parts.
Intended use m
• The maximum and minimum dimensions
of the used workpieces should not be
exceeded.
• Only use machines which are free from
defects. Keep safety precautions and
possible hazards in mind. Use only accor-
ding to instructions. Fully eliminate (or have
eliminated) any defects which can lead to
reduced safety.
• The safety, work and maintenance instruc-
tions of the manufacturer as well as the
technical data given in the calibrations and
dimensions must be adhered to.
• Relevant accident prevention regulations and
other, generally recognized safety-technical
rules must also be adhered to.
Residual risks m
Regularly check the cutting off wheel for any
defects.
• Health hazards for fingers and hands when
changing the cutting off wheel. Wear proper
working gloves.
• Health hazards when switching on the ma-
chine through the starting cutting off wheel.
• Risks through electric current if defective
electric connection cables are used.
• Health hazards through the running cutting
off wheel with long hair and loose clothing.
Installation
enough space to ensure safe and trouble-
free operation. The power tool is designed
Equipment Fig. 1
6.
Guard, flexible
7.
Saw shaft lock
8.
Cutting wheel
9.
Clamping jaw, flexible
10. Quick clamping lever
Commissioning
damaged, it should be carefully inspected
to ensure that it can perform its intended
function correctly. If in doubt, the part should
be replaced.
13
Non – skid footwear is recommended.
Wear restrictive hair covering to contain long
hair.
Use eye and ear protection. Always wear:
• ANSI – approved dust mask or respirator
when working around metal, wood, and
chemical dusts and mists.
• A full face shield if you are producing metal
filings.
• Ear protectors
Maintain proper footing and balance at all
times.
Do not reach over or across running machi-
nes.
• The machine may only be used, maintained
and operated by persons familiar with it and
instructed in its operation and procedures.
Arbitrary alterations to the machine release
the manufacturer from all responsibility for
any resulting damage.
• The machine may only be used with original
accessories and original tools from the
manufacturer.
• Any other use exceeds authorization. The
manufacturer is not responsible for any
damages resulting from unauthorized use;
risk is the sole responsibility of the operator.
Wear personal protective gear like a hair net
und closely fitting clothes.
• Even when all safety measures are taken,
some remaining hazards which are not yet
evident may still be present.
• Remaining hazards can be minimized by
following the instructions in „Safety pre-
cautions„, „Proper use„, and in the entire
operating manual
for working in enclosed rooms and has to be
installed on level and firm ground.
11. Clamping handle
12. Allen key (8 mm) (cut-off wheels repla-
cement)
13. Clamping jaw, fixed
14. Fastening bolt (transport)
• Be sure the switch is OFF before plugging In.
• Make sure tool has been cleaned and
properly lubricated.
• Check for damaged parts. Before using any
GB
Publicité
