Publicité
Les langues disponibles
Les langues disponibles
When ordering, please specify our part num-
bers, as well as type and construction year of
the device.
NOTE:
According to the applicable product liability
laws, the manufacturer of the device does not
assume liability for damages to the product or
damages caused by the product that occurs
due to:
• Improper handling,
• Non-compliance of the operating instruc-
tions,
• Repairs by third parties, not by authorized
service technicians,
• Installation and replacement of non-original
spare parts,
• Application other than specified,
• A breakdown of the electrical system that
• Metalworking can be dangerous if safe
and proper opera-ting procedures are not
followed.
• As with all machinery, there are certain
hazards involved with the operation of the
product. Using the machine with respect
and caution will considerably lessen the
possibility of personal injury. However, if
normal safety precautions are overlooked or
ignored, personal injury to the operator may
result. Safety equipment such as guards,
goggles, dust masks and hearing protec-
tion can reduce your potential for injury.
But even the best guard won't make up for
poor judgment, carelessness or inattention.
Always use common sense and exercise
GB
caution in the workshop. If a procedure feels
dangerous, don't try it. Figure out an alter-
native procedure that reels sater.
• REMEMBER: Your personal safety is your
responsibility.
• This machine was designed for certain ap-
plications only. We strongly recommend that
this machine not be modified and/or used
for any application other than that for which
it was designed. If you have any questions
relative to a particular application. DO NOT
use the machine until you have first contac-
ted the seller to determine if it can or should
be performed on the product.
WARNING: FAILURE TO FOLLOW THESE
RULES MAY RESULT IN SERIOUS PERSO-
NAL INJURY
• For your own safety, read instruction manual
before operating the tool. Learn the tool's
application and limitations as well as the
specific hazards peculiar to it.
• Keep guards in place and in working order.
• Always wear eye protection.
• Ground all tool's. If tool's equipped with
three prong plug, it should be plugged into
■
ADDITIONAL SAFETY INFORMATION
• Do not cut material that is too small to be
safely supported.
• Avoid awkward hand positions where a
sudden slip could cause a hand to move
into the cutting off wheel.
• Always keep hands and fingers away from
cutting off wheel.
• Do not attempt to cut material that is not
occurs due to the non-compliance of the
electric regulations and VDE regulations
0100, DIN 57113 / VDE0113.
We recommend:
Read through the complete text in the
operating instructions before installing and
commissioning the device. The operating
instructions are intended to help the user to
become familiar with the machine and take
advantage of its application possibilities in
accordance with the recommendations. The
operating instructions contain important infor-
mation on how to operate the machine safely,
professionally and economically, how to avoid
danger, costly repairs, reduce downtimes and
how to increase reliability and service life of
the machine.
In addition to the safety regulations in the
General safety information m
a three-hole electrical receptacle. If an
adapter is used to accommodate a two-
prong recentacle, the adapter plug must be
attached to a know ground. Never remove
the third prong.
• Remove adjusting keys and wrenches.
Form habit of checking to see that all ad-
justing tools are removed from tool before
turning it „on".
• Keep work area clean. Cluttered areas and
benches invite accidents.
• Don't use in dangerous environment. Don't
use power tools in damp or wet locations, or
expose them to rain. Keep work area.
• Keep children and visitors away. All children
and visitors should be kept a safe distance
from work area.
• Make workshop childproof. With padlocks,
master switches, or by removing starter
keys.
• Don't overcharche tool. It will do the job
better and be safer at the rate for which it
was designed.
• Use right tool. Don't overcharge tool or
attachment to do a job for which it was
designed.
• Wear proper appa el. No loose clothing,
gloves. Neckties, rings, bracelets, or other
jewelry to get caught in moving parts.
Nonslip footwear is recommended. Wear
protective hair covering to contain long hair.
• Always use saffety glasses. Wear safety
glasses (must comply with ANSI Z87.1)
Everyday eyeglasses only have impact
resistantienses. Also use face or dust mask
if cutting operation is dusty.
• Firmly fasten your work piece. Always use
clamping devices. Use both hands for ope-
rating the machine.
• Don't overreach. Keep proper footing and
balance at all times.
securely fastened or clamped.
• Do not attempt to cut material too fast while
cutting.
• Never start the angle grinder with the cutting
off wheel pressed against the stock.
• When cutting a large workpiece make sure
the material is in safe cutting position.
• Should any part of your angle grinder be
12
operating instructions, you have to meet the
applicable regulations that apply for the ope-
ration of the machine in your country.
Keep the operating instructions package
with the machine at all times and store it in a
plastic cover to protect it from dirt and mois-
ture. Read the instruction manual each time
before operating the machine and carefully
follow its information. The machine can only
be operated by persons who were instructed
concerning the operation of the machine
and who are informed about the associated
dangers. The minimum age requirement must
be complied with.
We have marked the points in this manual
that concern your safety with this sign m
• Maintain tools in top condition. Keep tools
sharp and clean for best and safest perfor-
mance. Follow instructions for lubricating
and changing accessories.
• Disconnect tools before servicing and
when changing accessories such as cut-off
wheels, bite, cutters, ate.
• Use recommended. The use of accessories
or attachments not recommended by the
seller may cause hazards or risk of injury to
persons.
• Reduce the risk of uninternational starting.
Make sure switch is in „off"position before
plugging in power cord.
• Check damaged parts. Before further use
of the tool, a guard or other part that is
damaged should be carefully checked to en-
sure that will operate properly and perform
its intended function check for alignment
of moving parts, binding of moving parts,
breakage of parts, mounting, and any other
conditions that may affecr itw operation. A
guard or other part that is damaged should
be properly repaired or replaced.
• Never leave tool running unattended. Turn
power OFF. Don't leave tool until it comes to
a complete stop.
• DRUGS, ALCOHOL MEDICATION. Do not
operate tool while under the influence of
drugs, alcohol or any medication.
• Make sure tool is disconnected from power
supply. While Motor is being mounted, con-
nected or reconnected.
• WARNING: The fragments generated by
certain metal and metal products can be
injurious to your health. Always operated
machinery in well ventilated areas and pro-
vide for proper removal.
• Secure your workpiece. Always use a
clamping device. Use both hands when ope-
rating the machine.
missing, damaged or fail in any way or any
electrical component fail to perform properly,
shut off switch and remove plug from power
supply outlet Replace missing, damaged or
failed parts before resuming operation.
• Save these instruction
Publicité
