Makita EA3200S Manuel D'utilisation page 26

Masquer les pouces Voir aussi pour EA3200S:
Table des Matières

Publicité

Les langues disponibles

Les langues disponibles

Fuel
CAUTION:
This saw is powered by petroleum products (gasoline
(petrol) and oil).
Be especially careful when handling gasoline (petrol).
Do not smoke. Do not allow gasoline to come near flames,
sparks or fire (explosion hazard).
Fuel mixture
This tool is powered by a high-performance air-cooled
two-stroke engine. It runs on a mixture of gasoline and two-
stroke engine oil.
The engine is designed for unleaded regular gasoline with
a min. octane value of 89 (R+M)/2. In case no such fuel is
available, you can use fuel with a higher octane value. This
will not affect the engine.
In order to obtain an optimum engine output and to
protect your health and the environment use unleaded
fuel only.
To lubricate the engine, use a synthetic oil for two-stroke
air-cooled engines (quality grade: JASO FC or ISO-L-EGD),
which has to be added to the fuel. The engine has been
designed for use of MAKITA synthetic two-stroke engine oil
and a mixture ratio of ONLY 50:1 to protect the environment.
In addition, a long service life and reliable operation with a
minimum emission of exhaust gases are ensured.
MAKITA synthetic two-stroke engine oil (50:1) is available in
the following sizes to suit your individual requirements:
2.6 floz. order number T-00745
6.4 floz. order number T-00739
In case MAKITA synthetic two-stroke engine oil is not available,
it is recommended to use a mixture ratio of 50:1 with other
synthetic two-stroke engine oils, as otherwise optimum opera-
tion of the engine cannot be guaranteed.
The correct mixture ratio:
50:1
when using MAKITA synthetic two-stroke engine oil,
i.e. mix 50 parts gasoline with 1 part oil.
50:1
when using other synthetic two-stroke engine oils
(quality grade JASO FC or ISO-L-EGD), i.e. mix 50
parts gasoline with 1 part oil.
NOTE:
For preparing the fuel-oil mixture first mix the entire oil quan-
tity with half of the fuel required, then add the remaining fuel.
Thoroughly shake the mixture before filling it into the chain
saw tank.
Chain oil
Use an oil with adhesive additive for lubricating the chain and
guide bar. The adhesive additive prevents the oil from being
flung off the chain too quickly.
We recommend the use of chain oil which is bio-degradable
in order to protect the environment. The use of bio-degradable
oil may even be required by local regulations.
The chain oil BIOTOP sold by MAKITA is made of special
vegetable oils and is 100% bio-degradable. BIOTOP has
been granted the "blue angel" (Blauer Umweltschutz-Engel)
for being particularly environment-friendly (RAL UZ 48).
26
Gasoline
50:1
MAKITA oil
+
1.0 Us-gal.
(3.7 l)
2.5 Us-gal.
(9.4 l)
5.0 Us-gal. (18.9 l)
It is not wise to add more engine oil than specified to
ensure safe operation. This will only result in a higher
production of combustion residues which will pollute
the environment and clog the exhaust channel in the
cylinder as well as the muffler. In addition, fuel consump-
tion will rise and performance will decrease.
Storage:
Fuels have a limited storage life. Fuel and fuel mixtures
age through evaporation, especially at high temperatures.
Aged fuel and fuel mixtures can cause starting problems
and damage the engine. Purchase only that amount of fuel,
which will be consumed over the next few months. At high
temperatures, once fuel has been mixed it should be used
up in 6-8 weeks.
Use only approved and marked containers for transport
and storage. Store fuel only in dry, cool and secure
locations!
AVOID SKIN AND EYE CONTACT
Mineral oil products degrease your skin. If your skin comes in
contact with these substances repeatedly and for an extended
period of time, it will desiccate. Various skin deseases may
result. In addition, allergic reactions are known to occur.
Eyes can be irritated by contact with oil. If oil comes into your
eyes, immediately wash them with clear water.
If your eyes are still irritated, see a doctor immediately!
Bio-degradable oil is stable only for a limited period of time. It
should be used within 2 years from the date of manufacture
(printed on the container).
50:1
other oil
2.6 floz. (75 cm
)
3
6.4 floz. (189 cm
)
3
12.8 floz. (378 cm
)
3

Publicité

Table des Matières
loading

Ce manuel est également adapté pour:

Ea3201s

Table des Matières