Yamaha RX-V565 Mode D'emploi page 33

y
• You can select the preset number at which the preset starts by
pressing hPRESET k / n or nCursor k / n while the front
panel display is in the state as shown in the below figure.
• To cancel registration, press nRETURN on the remote control.
Status
01:FM 87.50MHz
Preset number
During the automatic station preset, the upper area of
the screen changes as follows: READY → SEARCH
→ MEMORY each time a station is registered.
When registration is complete, "FINISH" appears
and the option menu screen automatically reappears.
When you press mOPTION on the remote control,
the screen returns to the original state.
Note
• Only Radio Data System broadcasting station are stored
automatically by automatic preset tuning (Europe model only).
Registering stations by manual station
preset
You can manually register AM stations or FM stations
with weak signals.
1
Tune in to a station referring to "Tuning in to
the desired FM/AM station (Frequency
tuning)" (see page 28).
2
Press DMEMORY (or hMEMORY).
"Manual Preset" appears on the front panel display,
followed soon by the preset number to which the
station will be registered.
y
• By pressing down DMEMORY (or hMEMORY) for more
than 2 seconds, you can skip step 3 and register the preset number
to be one higher than the last preset number.
3
Press EPRESET l / h (or hPRESET k / n)
on the remote control to select the preset
number to which the station will be
registered.
When you select a preset number to which no station
is registered, "Empty" appears on the display. When
you select a registered preset number, a registered
frequency is displayed on the right of the preset
number.
New registered frequency
01:Empty
Empty (or frequency that is currently
Flashing
registered to the preset number)
Preset
number
y
• You can select a preset number using the sNumeric keys.
Frequency
4
Press DMEMORY (or hMEMORY) again to
register.
When registration is complete, the screen returns to
the original state.
To end the operation, press mOPTION.
y
• To cancel registration, press nRETURN on the remote control
or leave the tuner without any operations for about 30 seconds.
Calling a preset station (Preset tuning)
You can call preset stations registered by automatic station
preset or manual station preset.
Press EPRESET l / h (or hPRESET k / n) to
select a preset number.
y
• Preset numbers to which no stations are registered will be skipped.
• When "No Presets" or "No Presets in Memory" is displayed it means that
no stations are registered. See page 28 and register stations.
• You can directly select a preset number by pressing a sNumeric
keys while calling a preset station. "Empty" appears on the display if
you enter a preset number to which no station is registered. "Wrong
Num." appears if you enter an invalid number.
• When you press sNumeric keys during normal tuning, a preset
number is selected. Set tuning mode to preset tuning mode using
EPRESET l / h (or hPRESET k / n) prior to the operation.
Clearing the preset station
1
Press NINPUT l / h repeatedly (or press
gTUNER) to switch the input source to
"TUNER."
2
Press mOPTION on the remote control.
The option menu screen for setting options of tuner
input appears on the front panel display.
3
Display "Clear Preset" using the nCursor k
/ n and press nENTER.
The following screen appears on the display.
01:FM 92.50MHz
Preset number of the registered station you want to clear.
y
• You can cancel the operation and return to the option menu screen
by pressing nRETURN on the remote control.
4
Select the preset number of the registered
station you want to clear using the nCursor
k / n and press nENTER.
The preset station registered to the selected preset
number is cleared. To clear the registration of
multiple preset numbers, repeat the above steps.
To end the operation, press mOPTION.
FM/AM tuning
29
En