Cleaning The Exhaust Filter; Spare Parts And Accessories; Recommendation; Before You Send In The Appliance - Dirt Devil paroly M7009 Série Mode D'emploi

5 Maintenance

5.3 Cleaning the exhaust filter

13
14

5.4 Spare parts and accessories

ATTENTION:
Only use original spare parts from the scope of delivery or those that you
have purchased by reordering.
„ Contact: ZPage 48, 'International Service'
„ Further information: Z www.dirtdevil.de

5.5 Recommendation

We recommend:
£
Swirl Y05 dust filter bags with MicroPor
“ “
Swirl , MicroPor and 'Y05' are registered trade marks of a company of the Melitta group and used with their permission.

5.6 Before you send in the appliance

WARNING:
Danger of injury! Never use a defective appliance! Always switch off the
appliance and disconnect it from the mains before starting troubleshoot-
ing ZChapter 4.3, 'Switching off'.
Before contacting your authorised Royal dealer, Royal service partner or
appliance market or before sending in the appliance, first follow the proce-
dure in the table to check if you can solve the problem yourself.
Problem Possible cause / solution
Filter bag The dust filter bag is full.
Change the dust filter bag ZChapter 5.1, 'Changing the
change indi-
cator (Fig. 1/
dust filter bag'.
16) appears
Nozzle, telescopic tube or suction hose is blocked.
in the display
Remove the obstacle. If necessary, use a long wooden
window.
stick (e.g. a broomstick) to do this.
The filters are dirty.
Clean the respective filter ZChapter 5.2, 'Cleaning the
motor protection filter' or ZChapter 5.3, 'Cleaning the ex-
haust filter'.
The vacuum The overheating protection has tripped (possibly due to
cleaner stops blocked suction channels, filters, or similar). Switch the
suddenly. appliance off and pull the plug out of the socket. Remove
the cause of overheating (e.g. by disassembling tele-
scopic tube and suction hose and removing the obstacle
and/or cleaning filters). Wait for about 45 minutes. After
the appliance has cooled off, you may switch it on again.
A
A
£
filtration
1. Switch off the appliance, ZChapter 4.3, 'Switching off'.
B
2. Push down the release catch of the exhaust filter cover and fold down
the cover (Fig. 13/A).
3. Separate the exhaust filter from the exhaust filter cover (Fig. 13/B).
4. Rinse the exhaust filter thoroughly by hand under clear running cold or
hand-warm water.
ATTENTION:
The filters are washable, but not suitable for cleaning in washing
machines or dishwashers. Do not use cleaning agents for cleaning.
Leave the filters to dry after cleaning them with water (approx. 24 hours
at room temperature). Only put them back into the appliance when they
are completely dry.
B
5. If the filter is damaged or deformed, replace it (ordering information
ZChapter 5.4, 'Spare parts and accessories').
6. Insert the new/cleaned exhaust filter back into the exhaust filter cover
(Fig. 13/B). Ensure that its bulges engage with the bulges of the cover.
7. Fit the exhaust filter cover on the bottom side first (Fig. 14/A) and then
push it back into its console (Fig. 14/B). It is easier if you push down the
release button when doing so.
8. Check the exhaust cover is securely in place.
Item number
7010022 Set of 5 dust filter bags and 1 motor protection filter
7009002 1 exhaust filter
7009018 1 telescopic tube extension
7020008 Accessory set consisting of: Accessory holder, Uphol-
stery nozzle, Furniture brush, Crevice nozzle
M203 1 parquet brush
M209 1 turbo brush
M219 1 mini turbo brush
NOTE:
Insert the bag in direction 'A'.
Problem
The cleaning The bypass vent (Fig. 1/24) is open.
results are
Close the bypass vent (Fig. 1/24).
unsatisfacto-
The attached nozzle is unsuitable.
ry in spite of
Change the nozzle, ZChapter 3.2, 'Assembly'.
the appli-
The position of the 'carpet/hard floor' selector (Fig. 1/28)
ance work-
is unsuitable.
ing correctly.
Set the "carpet/hard floor" selector (Fig. 1/28) to the cor-
rect position for the type of floor, ZChapter 4.2, 'Vacuum
cleaning', step 5.
The dust filter bag is full.
Change the dust filter bag ZChapter 5.1, 'Changing the
dust filter bag'.
The filters are dirty.
Clean the respective filter ZChapter 5.2, 'Cleaning the
motor protection filter' or ZChapter 5.3, 'Cleaning the ex-
haust filter'.
Nozzle, telescopic tube or suction hose is blocked.
Remove the obstacle. If necessary, use a long wooden
stick (e.g. a broomstick) to do this.
NOTE:
If you cannot solve the problem following these instructions, contact the
Royal Appliance customer service (ZPage 48, 'International Service').
Description
Possible cause / solution
15