Operating Times; Symbols Machine; Normal Intended Use; Risidual Risks - ATIKA BWS 400 Notice Originale - Consignes De Sécurité - Pièces De Rechange

Operating times

Before initiating the device please observe the provisions pertaining to
corresponding laws (regional provisions) for the noise control.

Symbols machine

Carefully read opera-
tor's manual and the
safety instructions be-
fore starting the
machine and observe
the instructions when
operating.
Risk of injuries of
fingers and hands by
the saw blade.
Wear eye and ear
protection.
Direction of saw blade rotation.
This product complies with European regulations specifically
applicable to it.
Electrical devices do not go into the domestic rubbish.
Give devices, accessories and packaging to an eco-
friendly recycling.
According to the European Directive 2012/19/EU on
electrical and electronic scrap, electrical devices that are
no longer serviceable must be separately collected and
brought to a facility for an environmentally compatible
recycling.
Symbols operating instructions
Threatened hazard or hazardous situation. Not observing this
instruction can lead to injuries or cause damage to property.
Important information on proper handling. Not observing this

instruction can lead to faults.
User information. This information helps you to use all the

functions optimally.
Assembly, operation and servicing. Here you are explained
exactly what to do.
Please refer to the attached
assembly and
instruction sheet for references to
figure numbers in the text.
...

Normal intended use

 This machine is designed for cross cutting firewood in the house and
hobby field.
Cutting round material having a diameter smaller than 30 mm or greater

than 120 mm is not allowed as these pieces can not be held safely.
 The length of the material to be cut must not exceed 1000 mm. The
length of the material must be 200 mm as a minimum.
 Only high-quality saw blades acc. to EN 847-1 up to a max. diameter of
400 mm must be used.
 Because it has no extraction device this machine must only be used
outdoors.
10
Shut off engine and
remove power cord
before performing
cleaning, maintenance
or repair work.
Wear protective gloves!
Wear safety shoes.
operating
Only work pieces are allowed to be processed which can be safely placed

and held in the jigging device.
The use of saw blades made of HSS steel (high-alloy high speed steel) is

not permitted since this steel is hard and brittle. Risk of injury through saw
blade breakage and expulsion of saw blade pieces.
 The intended usage also includes compliance with the operating,
servicing and repair conditions prescribed by the manufacturer and
following the safety instructions included in the instructions.
The relevant accident prevention regulations for the operation as well as

the other generally acknowledged occupational medicine and safety rules
must be complied with.
 Any other use is deemed not to be intended use. The manufacturer is not
liable for any type of damage resulting from this: the user bears the sole
risk.
Unauthorized modifications to the saw preclude any liability of the

manufacturer for resulting damages of any kind.
The saw may only be equipped, used and serviced by persons who are

familiar with it and have been instructed on the hazards. Repair works
may only be carried out by us or by a customer service agent nominated
by us.
The machine may not be used in a potentially explosive environment or

be exposed to rain.
Metallic parts (wires etc.) have unconditionally to be removed from the

material to be cut.

Risidual risks

Even if used properly, residual risks can exist even if the relevant safety
regulations are complied with due to the design determined by the intended
purpose.
Residual risks can be minimised if the "Safety instructions" and the "Normal
intended use" as well as the whole of the operating instructions are observed.
Observing these instructions, and taking proper care, will reduce the risk of
personal injury or damage to the equipment.
Danger of injury of fingers and hands by the tool (saw blade) or work

piece, e.g. when replacing the saw blade.
 Injury by catapulted workpiece parts.
 Throwback of the workpiece or workpiece parts.
Breaking or catapulting of saw blade.

Risk from electricity, by using non-standard electrical connections.

 Touching live parts of opened electrical components.
 Impairment of hearing when working on the machine for longer periods of
time without ear protection.
 Emission of harmful wood dusts. Wear therefore a protective mask.
 Noise emission: Use saw blades designed for noise reduction and keep
the machine in a good condition.
In addition, in spite of all the precautionary measures taken, non-obvious
residual risks can still exist.

Safe working

Woodworking machines can be dangerous if not used properly. If
electrical tools are used, the fundamental safety precautions must be
met to preclude the risks of fire, electric shock and injuries to persons.
Before starting this device, read and keep to the following advice. Also
observe the preventive regulations of your professional association and
the safety provisions applicable in the respective country, in order to
protect yourself and others from possible injury.
Pass the safety instructions on to all persons who work with the

machine.

Keep these safety instructions in a safe place.
Make yourself familiar with the equipment before using it, by

reading and understanding the operating instructions.
Be attentive. Be careful what you do. Behave sensibly when

working. Do not use the device when you are tired or under the
influence of drugs, alcohol or medica-ments. One moment of care-
lessness when using the device can result in serious injuries.