Important Safety Precautions - Jiffy ROGUE Mode D'emploi

Jiffy® E-Z Connect™ Collar
Connect drill assembly to powerhead by sliding E-Z Connect™
Collar down and pulling clevis pin out. Then slide drill assembly
onto the powerhead output shaft. Line up the hole in the drill
assembly to the hole in the output shaft and insert clevis pin
through drill assembly and output shaft. Slide E-Z Connect™
Collar up over clevis pin and twist the collar clockwise a ¼ of a
turn to lock pin in place.
Note: Do not remove clevis pin from yellow collar tether.

IMPORTANT SAFETY PRECAUTIONS

Please read this manual carefully. Operate your equipment
according to the safety instructions and recommendations found
throughout this manual. Anyone who uses this equipment must
read and fully understand the instructions and be familiar with its
operation.
To receive the greatest possible performance and satisfaction
from your Jiffy® Power Ice Drill and to reduce the risk of injury, it
is important that you read and understand the assembly,
operating, maintenance, and safety instructions before using your
Jiffy® Power Ice Drill. Contact Feldmann Engineering if you do
not understand any of the instructions in this manual.
Your Jiffy® Power Ice Drill is designed and manufactured to
provide safe and dependable operation, provided it is operated in
accordance with the following safety precautions.
Preventing accidents is the responsibility of every power
equipment operator. The safety precautions identified in this
manual must be fully understood and followed by every operator
of this Jiffy® Power Ice Drill. Review the safety precautions
frequently and never take chances.
Take the time to become familiar with your Jiffy® Power Ice Drill
and its components, then operate it in a safe manner. Study the
appropriate sections of this manual for the description of the
controls and function of your Jiffy® Power Ice Drill. Teach the
safety precautions to all persons who use your Jiffy® Power Ice
Drill.
CHECK BEFORE STARTING YOUR JIFFY® ICE DRILL:
1. Be sure the control switch is in the proper position for either
drilling position (clockwise) or hole clean out position
(counterclockwise).
2. Inspect the machine for proper condition and operation,
paying special attention to the throttle control assembly and
drill assembly.
+ TO REDUCE THE RISK OF INJURY FROM THE
TURNING DRILL ASSEMBLY OR FROM REACTIVE
FORCES, THE THROTTLE ASSEMBLY AND RELATED
MECHANISM MUST MOVE FREELY AND RETURN
IMMEDIATELY TO THE DISENGAGED POSITION WHEN
RELEASED.
NEVER OPERATE YOUR JIFFY® ICE DRILL IF IT HAS
BEEN DAMAGED, IMPROPERLY ADJUSTED OR NOT
COMPLETELY AND SECURELY ASSEMBLED.
TO REDUCE THE RISK OF INJURY FROM REACTIVE
FORCES, THE OPERATOR MUST HAVE A FIRM GRIP
ON THE MACHINE AND A GOOD FOOTHOLD ON THE
ICE BEFORE STARTING THE DRILL AND OPENING THE
THROTTLE.
KEEP HANDS, FEET, HAIR, DRAW STINGS, SCARVES,
HATS AND LOOSE CLOTHING AWAY FROM ANY
MOVING PARTS OF THE UNIT.
Battery Safety and Use Information
For the proper use, maintenance and storage of the battery, it
is important that you read and understand the instructions
given in this manual.
To avoid serious injury, risk of fire, explosion and danger of
electric shock or electrocution:
1. Do not probe the charger with conductive materials. The
charging terminals hold 120 volts.
2. If the battery pack case is cracked or damaged, DO NOT
insert anything into the charger.
3. Do not charge these battery packs with any other type of
charger.
4. Do not allow any type of liquid to get inside the charger
5. Do not try to use the charger for any other purpose than
what is presented in this manual.
Warning / Caution:
1. Do not charge the battery pack in the rain or any wet
conditions.
2. Do not immerse the battery in water or other liquid.
Safety Notes and Precautions:
1. Do not disassemble the battery.
2. Keep battery away from children.
3. Do not expose the battery to salt water.
4. Store battery in a warm (35°F/2°C - 100°F/38°C), dry
location.
5. Do not place the battery in high temperature (above
100°F/38°C) locations such as near a fire or heater etc.
6. Do not try to solder any electrical connections on the
battery.
7. Please handle the battery with care. Breaking any part of
the battery due to neglect could cause personal injury.
8. In the event the battery leaks and contents get in your
eyes, do not rub your eyes. Rinse your eyes with water
and get immediate medical help.
9. Discontinue use of the battery if it leaks any fluids,
unusual smell occurs, changes color, changes shape or
appears abnormal in any way.
To avoid risk of fire, electric shock or electrocution:
1. Do not use a damp cloth or detergent on the battery
charger.
2. Always remove the battery pack before cleaning,
inspecting or performing any maintenance on the battery
or charger.
3. Do not allow the battery pack or charger to overheat. If
they feel warm, allow them to cool down.
4. Charge battery above 35°F/2°C.
5. Keep the ventilation slots on the charger clear.
4