Operating Elements And Connections; Front Panel; Rear Panel; Safety Notes - IMG STAGELINE MPX-2 Mode D'emploi

Please unfold page 3. Then you can always see the
GB
operating elements and connections described.

1 Operating Elements and Connections

1.1 Front panel

1 5-step LED VU-meter
2 Power switch with power LED
3 Switch for microphone announcements: With the
switch pressed, the levels of the channels CH 1
and CH 2 are attenuated by 15 dB.
4 Switch for the prefader listening feature: According
to the position of the switch, the channel CH 1 or
the channel CH 2 can be monitored via head-
phones connected to the jack (11).
5 Volume control for the microphone
6 Volume control for the headphones connected to
the jack (11)
7 Input selector switches PHONO – CD/LINE for the
channels CH 1 and CH 2
8 Volume controls (faders) for the channels CH 1 and
CH 2
9 6.3 mm jack (unbal.) for connecting a mono micro-
phone
10 Crossfader for crossfading between the channels
CH 1 and CH 2
11 6.3 mm jack for connecting stereo headphones
(impedance ≥ 8 Ω)

1.2 Rear panel

12 Low-voltage jack for connecting the supplied plug-
in transformer (230 V~/50 Hz/10 VA)
13 Phono output jacks REC for connecting a sound
recorder
14 Phono output jacks AMP for connecting an ampli-
fier
15 Phono input jacks CD/LINE for the channels CH 1
and CH 2 for connecting units with line level (e. g.
tuner, CD player, cassette recorder)
16 Phono input jacks PHONO for the channels CH 1
and CH 2 for connecting turntables with magnetic
system
17 GND connection for a common ground, e. g. for
turntables
6

2 Safety Notes

The mixer and the plug-in transformer correspond to
the directive for electromagnetic compatibility 89/336/
EEC. The transformer also corresponds to the low
voltage directive 73/23/EEC.
Attention! The plug-in transformer is supplied with
hazardous mains voltage (230 V~). Inexpert handling
or modification of the plug-in transformer may cause
an electric shock hazard. Furthermore, any guaran-
tee claim will expire if the transformer or the mixer
has been opened.
Please observe the following items in any case:
The mixer and the plug-in transformer are suitable
for indoor use only. Protect them against dripping
water and splash water, high air humidity, and heat
(admissible ambient temperature range 0 – 40 °C).
Even with the mixer switched off, there will be a low
power consumption by the plug-in transformer.
Do not operate the mixer or immediately disconnect
the plug-in transformer from the mains socket
1. in case of visible damage to the mixer or to the
transformer,
2. if a defect might have occurred after the unit was
dropped or suffered a similar accident,
3. if malfunctions occur.
In any case the units must be repaired by skilled per-
sonnel.
For cleaning only use a dry, soft cloth, by no means
chemicals or water.
No guarantee claims for the unit and no liability for
any resulting personal damage or material damage
will be accepted if the mixer or the plug-in trans-
former is used for other purposes than originally in-
tended, if it is not correctly connected, operated, or
not repaired in an expert way.
If the units are to be put out of operation
definitively, take them to a local recycling
plant for a disposal which is not harmful to
the environment.

3 Applications

The stereo DJ mixer MPX-2 with two stereo input
channels and a DJ microphone connection is suitable
for any private or professional DJ applications. The
mixer can either be placed as desired or be installed
into a console.
4 Setting the Mixer into Operation
1) Connect the audio sources to the corresponding
input jacks:
– jacks CD/LINE (15) for connecting units with line
level (e. g. tuner, CD player, cassette recorder)
– jacks PHONO (16) for connecting turntables with
magnetic system;
connect the ground connections of the turntables
to the terminal screw GND (17)