Napoleon LA400 Mode D'emploi page 4

4
Cylinder Specification/Gas Hook Up
EN
This gas barbecue is certified under Canadian and American National Standards, CAN/CSA 1.6 – 2005 and
ANSIZ21.58 -2005 respectively for outdoor gas grills and should be installed to conform with local codes.
In absence of local codes, install to the current CAN/CGA-B149.1 Propane Installation Code in Canada or to
the National Fuel Gas Code, NFPA54/ANSI Z223.1 in the United States.
If a rotisserie motor is used, it must be electrically grounded in accordance with local codes or, in absence
of local codes, with the current CSA C22.1 Canadian electrical code in Canada or the National Electrical
Code, ANSI/NFPA 70 in the United States.
California Proposition 65: The burning of gas fuel creates by-products, some of which are on the list as
substances known by the State of California to cause cancer or reproductive harm. When cooking with
gas, always ensure adequate ventilation to the unit, to minimize exposure to such substances.
Propane Cylinder Specifications
WARNING!
may occur.
A dented or rusty cylinder may be hazardous and should be checked by your propane supplier. Never use a
cylinder with a damaged valve. Use only a propane supply cylinder constructed and marked in accordance
with the specifications for LP-gas cylinders of the National Standard of Canada, CAN/CSA-b339, Cylinders,
Spheres and Tubes for Transportation of Dangerous Goods; and Commission, as applicable or the
Specifications for LP-Gas Cylinders of the U.S. Department of Transportation (D.O.T.). This appliance has
been designed for use with a 20 lb. (9.1 kg) size propane cylinder only (not supplied).
The propane cylinder must be provided with a cylinder connection device compatible with the connection
for outdoor cooking appliances. The propane cylinder must be provided with a shut-off valve terminating
in a propane cylinder valve type QCC1, and a safety relief device having direct communication with the
vapor space of the cylinder. The cylinder supply system must be arranged for vapor withdrawal and the
cylinder shall include a collar to protect the cylinder valve. The cylinder shall incorporate a listed OPD
(overfill protection device). Do not store a spare LP-gas cylinder under or near this appliance. Never fill
the cylinder beyond 80 percent full.
Propane Cylinder Installation
Cylinder Connection: Ensure that the gas regulator hose is kink free. Remove the cap or plug from
the cylinder fuel valve. Insert the black QCC1 regulator nipple onto the QCC1 fuel valve. Hand tighten
clockwise. Do not use tools. Leak test all joints prior to using the barbecue. A leak test must be performed
annually, and each time a cylinder is hooked up, or if a part of the gas system is replaced.
• Check that the cylinder valve is closed by turning the knob clockwise.
• Check that the grill's burner knobs are in the off position.
• Open cabinet doors.
• Place the cylinder into the tank holder in bottom of shelf.
• Position the cylinder so that the valve faces toward the front of the unit.
• Attach regulator hose.
WARNING!
Replacement pressure regulators and hose assemblies must be specified by the manufacturer. Do not store a
spare propane cylinder on the shelf beneath the barbecue. The regulator must be attached so that no part of
the hose touches the underside of the grill or drippan. A fire will result if these directions are ignored.
The regulator supplies a pressure of 11 inches. water column to the gas grill and has a QCC1 type fitting.
Cylinders to be used with this unit must be supplied with a QCC1 cylinder valve. A QCC1 cylinder has a
positive seating connection, which will not allow gas flow until a positive seal has been achieved. It is also
equipped with an excess flow device. In order to attain full flow to the grill, the valves must be in the off
position when the cylinder valve is turned on.
www.napoleongrills.com
If these instructions are not followed exactly, a fire causing death or serious injury
Use only the pressure regulator and hose assembly provided with this barbecue.