Extension Cords; Noise And Vibration Data; Combinations Of Cutting Attachments And Deflectors; Spare Parts And Accessories - Stihl FSA 57 Notice D'emploi

English
The charging times are indicated at
www.stihl.com/charging-times.
20.4

Extension Cords

If an extension cord is used, the cross sectional
area of its conductors must meet the following
minimum requirements – depending on the line
voltage and length of the extension cord:
If rated voltage on the rating label is 220V to
240V:
– Cord length up to 20 m: AWG 15 / 1.5 mm²
– Cord length 20 m up to 50 m: AWG 13 /
2.5 mm²
If rated voltage on the rating label is 100V to
127V:
– Cord length up to 10 m: AWG 14 / 2.0 mm²
– Cord length 10 m up to 30 m: AWG 12 /
3.5 mm²
20.5

Noise and Vibration Data

K-value (uncertainty) for sound pressure levels is
2 dB(A). K-value (uncertainty) for sound power
levels is 2 dB(A). K-value (uncertainty) for vibra‐
tion levels is 2 m/s².
STIHL recommends that you wear hearing pro‐
tection.
– Sound pressure level L
to EN 50636-2-91: 74 dB(A)
– Sound power level L
EN 50636-2-91: 89 dB(A)
– Vibration measurement a
ing to EN 50636-2-91; control handle and loop
handle: 4,0 m/s²
The vibration values quoted above have been
measured according to a standardized test pro‐
cedure and may be used to compare electric
power tools. Depending on the type of usage,
the vibrations that actually occur may differ from
the values quoted. The vibration values quoted
may be used for an initial assessment of the
user's exposure to vibrations. The actual expo‐
sure to vibrations has to be estimated. This proc‐
ess may also take into account times during
which the electric power tool is switched off and
times during which it is switched on but running
off load.
For information on compliance with Vibration
Directive 2002/44/EC visit www.stihl.com/vib.
38
measured according
pA
measured according to
wA
measured accord‐
hv

21 Combinations of Cutting Attachments and Deflectors

20.6 REACH
REACH is an EC regulation and stands for the
Registration, Evaluation, Authorisation and
Restriction of Chemical substances.
For information on compliance with the REACH
regulation see www.stihl.com/reach.
21 Combinations of Cutting
Attachments and Deflec‐
tors
21.1 STIHL FSA 57 brushcutter
The following mowing heads may be mounted
with the deflector:
STIHL AutoCut C 3-2 mowing head:
– with round, low-noise mowing line with a
diameter of 1.6 mm or 2.0 mm
PolyCut 3-2 mowing head
– with blades
– with round, low-noise mowing line with a
diameter of 1.6 mm or 2.0 mm
22 Spare Parts and Accesso‐
ries
22.1

Spare parts and accessories

These symbols indicate original STIHL
spare parts and original STIHL acces‐
sories.
STIHL recommends the use of original STIHL
spare parts and accessories.
Despite ongoing market observation, STIHL is
unable to judge the reliability, safety and suitabil‐
ity of other manufacturers' spare parts and
accessories; accordingly, STIHL cannot warrant
for the use of those parts.
Original STIHL spare parts and original STIHL
accessories are available from STIHL dealers.
23 Disposal
23.1 Disposal of Trimmer, Battery
and Charger
Contact your STIHL servicing dealer for informa‐
tion on disposal.
► Dispose of the trimmer, deflector, cutting
attachment, battery, charger, accessories and
packaging in accordance with local regulations
and environmental requirements.
0458-806-9621-B.VA0.M20.