Functions - diagral SI200 Mode D'emploi

FIG. E
Installing the Aerials
Aerial tubes. Holding groove
Take the two aerial tubes that are packed with the alarm.
Slide the two aerials all the way into the tubes. Attach the aerial end pieces.
1
Push the tubes into the vertical grooves, using the flat bladed screwdriver to position them.
2
FIG. F
Selecting the functions
The bar of 3 micro switches allows selection of:
delay in setting off the siren,
base unit to report or not report with audible messages.
Micro switch Positions
1) Active only for emergency call, tamper protection, fire, and advance alarm.
(2) The report of sound messages is the siren repeating the base unit sound messages when the system is
set and unset. It only works when the base unit is in normal mode (fixed to the wall). The sound message
report is the same whatever command is entered.
(3) The report of sound messages is, however active while the siren is being installed.

Functions

Rings immediately if there is an intruder
10 second ring delay
60 second ring delay
Silent alert (1)
No report of messages received (2)(3)
Report of messages received
when system is being Set or Unset (2)
GB
FIG. G
Fitting the batteries and closing the siren
Insert the 4 batteries in the siren. Press the OFF key on a remote control or on the keypad.
If the siren gives an audible signal, the personalised radio code is properly registered. If the
siren does not respond, remove the 4 batteries and repeat the procedure to transfer the per-
sonalised radio code to the siren.
FIG. H
Tamper protection
Important the anti tamper protection against the case being opened and the aerials
being cut is not active while the siren is being installed. It becomes active after the first com-
mand to Set the system (part or fully set Group A or Group B) is received, or if the anti tam-
per sensor is engaged for more than 5 seconds. You are strongly advised to wait until the
siren is fixed to the wall before sending any sort of command to Set.
Anti tamper sensor
in position 2 as shown in
FIG. I
Installation
Fix the base to the wall using the dome headed screws and washers provided or others if
1
they are more suitable. Leave enough room below the base for a screwdriver to screw up the
fixing screw.
Clips the siren onto the base and tighten the fixing screw.
2
Send a Set command (Part set, Fully set Group A or Group B): the siren will give an
3
audible signal. Then send an Off command.
Anti tamper protection is now active. The siren will ring if pulled from the wall or opened,
and if the 2 aerials are cut.
The siren is now attached to the wall. You should regularly carry out a real test, setting off the
siren.
CHECKING AND CHANGING THE BATTERIES
The alarm siren constantly checks the condition of the batteries. It indicates low batteries with
an audible staccato message "beep, beep,... beep, beep ..." after every command from the
remote control to Set or Off the system. A spoken indication of low batteries follows the
audible reporting messages from the base unit, if this function has been activated.
Change all four batteries at the same time, as follows:
Take a remote control and a small Phillips screwdriver and stand on a level with the siren
1
so that you can open it.
Unscrew the locking screw
2
Unclip the siren while holding down the OFF key on the remote control or the keypad to
3
avoid setting off the alarm siren by releasing the tamper protection sensor.
Remove all the batteries and wait 5 minutes before connecting the new batteries as des-
4
cribed in Fig. G.
Replace the siren on the base and tighten the fixing screw.
5
Send the Set command (Part set, Fully set or Group A or B) followed by an Off command.
6
Do a real siren test.
7
The siren is now ready again.
20
Slot for anti tamper sensor. Insert the anti tamper sensor into its slot
Fig. H.
(Fig.
(Fig. B).
GB
B).
21