Battery Pack - Metabo KT 18 LTX 66 BL Notice Originale

If battery fluid leaks out and comes into
contact with your skin, rinse immediately
with plenty of water. If battery fluid leaks out
and comes into contact with your eyes, wash them
with clean water and seek medical attention
immediately!
Transport of li-ion battery packs:
The shipping of li-ion battery pack is subject to laws
related to the carriage of hazardous goods (UN
3480 and UN 3481). Inform yourself of the currently
valid specifications when shipping li-ion battery
packs. If necessary, consult your freight forwarder.
Certified packaging is available from Metabo.
Only send the battery pack if the housing is intact
and no fluid is leaking. Remove the battery pack
from the machine for sending. Prevent the contacts
from short-circuiting (e.g. by protecting them with
adhesive tape).
Reducing dust exposure:
WARNING - Some dust created by power
sanding, sawing, grinding, drilling, and other
construction activities contains chemicals known to
cause cancer, birth defects or other reproductive
harm. Some examples of these chemicals are:
- Lead from lead-based paints,
- Crystalline silica from bricks and cement and
other masonry products, and
- Arsenic and chromium from chemically treated
lumber.
Your risk from these exposures varies, depending
on how often you do this type of work. To reduce
your exposure to these chemicals: work in a well-
ventilated area, and work with approved safety
equipment, such as those dust masks that are
specially designed to filter out microscopic
particles.
This also applies to dust from other materials such
as some timber types (like oak or beech dust),
metals, asbestos. Other known diseases are e.g.
allergic reactions, respiratory diseases. Do not let
dust enter the body.
Observe the relevant guidelines and national
regulations for your material, staff, application and
place of application (e.g. occupational health and
safety regulations, disposal).
Collect the particles generated at the source, avoid
deposits in the surrounding area.
Use suitable accessories for special work. In this
way, fewer particles enter the environment in an
uncontrolled manner.
Use a suitable extraction unit.
Reduce dust exposure with the following measures:
- do not direct the escaping particles and the
exhaust air stream towards yourself or nearby
persons or towards dust deposits,
- use an extraction unit and/or air purifiers,
- ensure good ventilation of the workplace and keep
it clean using a vacuum cleaner. Sweeping or
blowing stirs up dust.
- Vacuum or wash protective clothing. Do not blow,
beat or brush protective gear.
5. Overview
See pages 2 and 3.
1 2 Clamping lever (for rip fence)
2 Cutting indicator
3 Adjusting screw (for adjusting the 45° saw
blade angle).
4 Scale (diagonal cut angle)
5 2 Locking screws (diagonal cuts)
6 Undercut button
7 Adjusting screw (for adjusting the 0° saw blade
angle).
8 Marking (for reading off the cut width when the
rip fence is used)
9 Read-off edge "FS" (for reading off the cutting
depth when the guide rail "FS" is used)
10 Read-off edge (for reading off cutting depth)
11 Handle
12 Handle (additional handle)
13 Locking button (for setting cutting depth)
14 Lever (for changing the saw blade)
15 Rotary button (for setting a clearance-free fit on
the guide rails)
16 Guide plate
17 Locking button
18 Trigger
19 Battery pack release button
20 Speed preselection wheel
21 Capacity indicator button
22 Capacity and signal indicator

23 Battery pack

24 Hexagon wrench / Storage for hexagon wrench
25 Guide grooves to place the machines on guide
tracks from different manufacturers
26 Dust bag
27 Connector (extraction connection piece / dust
ejection)
28 Preselection wheel for precision setting of the
cutting depth
29 Glass guard
30 Saw blade fixing screw
31 Outer saw blade flange
32 Saw blade
33 Inner saw blade flange
6. Initial Operation and Setting
Remove the battery pack from the machine
before any adjustment or maintenance is
carried out. Before fitting the battery pack, make
sure that the machine is switched off.
6.1 Battery pack
We recommend the use of LiHD battery packs with
a capacity of at least 5.5 Ah. If other battery packs
are used, a reduced performance is to be expected.
Charge the battery pack (23) before use.
Recharge the battery pack if performance dimin-
ishes.
ENGLISH en
15