SYNQ SMD.5 Mode D'emploi page 5

ENGLISH
FUNCTIONS (REAR)
25. POWER SWITCH: Used to switch the mixer on and off.
26. MAINS INPUT: with IEC socket and integrated fuse holder, connect the supplied mains cable here.
27. SUBWOOFER LEVEL: Controls the level of the subwoofer output. Start from zero and slowly turn in
clockwise direction until the amount of low frequencies seems to be OK for you.
28. X-OVER FREQ. control: (crossover frequency control) adjusts the cutoff frequency of the subwoofer low
pass filter. This crossover frequency can be set in a range of 30 to 200Hz. It's up to you to adapt its
position to your own taste. For most subwoofers 100Hz to 150Hz seems to be the best choice.
29. SUBWOOFER OUTPUT connector: this male XLR-connector can be connected to both unbalanced
and balanced inputs of subwoofer amplifiers. The cutoff frequency and level of this output are adjustable.

For balanced use, please follow these conventions:
Pin1 = Ground ~ Pin2 = Hot (+) ~ Pin3 = Cold (-)

For unbalanced use, connect Pin3 (-) to Pin1 (ground/shield)
30. MASTER1 BALANCED OUTPUT: The XLR-connectors can be used to connect the mixer to any
balanced amplifier input, using special balanced signal cables.
31. MASTER1 UNBALANCED OUTPUT: The same output signal as on the balanced master output(19) but
unbalanced. Can be used to connect unbalanced amplifiers.
32. MASTER2 UNBALANCED OUTPUT: Can be used to connect for example a second serie of
unbalanced amplifiers.
33. RECORD OUTPUT: Carries the same signal as the master outputs but is not influenced by the master
level and balance controls. Used to connect analog recording equipment. You can also connect a
computer for direct digital recording, see USB connection (38).
34. GROUND (GND) CONNECTION: Many Turntables have a GND-connection. It is preferable to connect
this signal ground to the GND-connector. If your turntable does not have a ground wire, you don't have
to use this connector.
35. INPUT CHANNEL PHONO/LINE: used to connect two different audio signals: phono or line. Use the
push button below to change the input between line and phono. The input source selector (7) on the
front determines which input will be active: phono/line (35) or USB/line (36).
36. INPUT CHANNEL USB/LINE: used to connect two different audio signals: USB or line. Use the push
button below to change the input between USB and line. The input source selector (7) on the front
determines which input will be active: phono/line (35) or USB/line (36).
37. DJ-MIC INPUT: 6,3mm jack. Accepts an unbalanced microphone with 1/4" mono jack. This input is
mainly used as DJ-microphone.
38. USB CONNECTION 1: You can connect any PC through this USB connection. The PC/Mac will detect
your mixer as a sound card, normally no drivers are needed. Since this USB port is bidirectional you are
able to play music on your computer and mix this music with other sources like CD, phono, etc. At the
same time you can record your mix on your computer with the same USB connection!
39. USB CONNECTION 2: You can connect any PC through this USB connection. The PC/Mac will detect
your mixer as a sound card, normally no drivers are needed. Please note that this USB port can only be
used to play music on your computer and mix this music with other sources like CD, phono, etc.
CHANGING THE CROSSFADER
 Remove the fader knob from the cross fader.
 Remove the 2 screws that keep the cross fader in place.
 Gently remove the fader and the cover plate from their position.
 Unplug the cross fader from the cable (unplug the cable by pulling the connector, NOT the cable!)
 Press the new cross fader on the cable.
 Put the cross fader back in place with the small cover plate and the 2 screws.
SYNQ
®
OPERATION MANUAL
5/36
ENGLISH
Done!
SPECIFICATIONS
Power Supply:
Power consumption:
Fuse:
Frequency response:
THD + noise:
S/N Ratio (IHF-A):
Micro inputs:
Line/CD inputs:
Phono inputs:
Record output:
Master output:
Master output:
Tone controls CH1CH5:
Tone controls DJ MIC:
Headphone:
Dimensions:
Weight:
You can download the latest version of this user manual on our website: www.beglec.com
SMD-5 SYNQ
®
AC 230 V, 50Hz
28W
20mm glass fuse 250V 1A slow
20-22.000Hz (+/-3dB)
<0.1% @ 1kHz, 0dB
>80dB @ 1kHz.
1.5mV @ 10kΩ
150mV @ 22kΩ
3mV @ 47kΩ
775mV @ 600Ω
1.5V @ 4k7Ω unbal.
850mV @ 600Ω bal.
+12dB / -26dB @ 10kHz / 1,3kHz / 50Hz
+/-12dB @ 10kHz / 2,5kHz / 70Hz
180mW@75Ω
483(W) x 220(H) x 104(D)mm (19" / 5U)
Mounting depth = 85mm
5,2kg
Every information is subject to change without prior notice
6/36
OPERATION MANUAL
SMD-5