Practical Notes; Operating Potentiometer; Technical Data - DOLD SAFEMASTER C UG 6980 Manuel D'utilisation

Practical Notes

Operating mode
Manual or auto start is chosen by wiring. On manual start S21 has to be
connected to ST1! via an NO push button. For auto start S21 is connected
to ST2. If both inputs are connected to S21 the unit goes into safe failure
mode. A restart or new start of the device has to be made. When selecting
the safety function 2-hand control (3), only automatic start is possible.
Line fault detection e.g. monitoring of ON-button
If the On-button pressed more than 3 s the adequate output contacts of the
safety function can't be switch. The output contacts can be energized when
the On-button pressed again (0.1 s < t
A line fault is detected if the On-button more than 10 s is actuated. The
output contacts of the adeauate safety function can only be energized with
a reset or re-start with on an off switching of power supply.
Reset and external failures:
The reset input is used to reset external failures (application failures or
removable external failures as e.g. a line fault on reset button). If the reset
signal is connected to the input for more than 3 sec the unit makes a reset.
A new reset is only possible when the reset signal had been switched off
temporarily.
If an external failure occurs because both input channels of a safety function
did not switch on or off within the simultanious time, a reset is only possible
if both channels are switched to off state after removing failure cause.
Setting
On the variant /0_ _ the safety function can be set via rotary switch.
Possible functions:
Fct. Safety function
1
2 Safety gate
3 Two-hand control
4 Safety mat / Safety edge
5 Exclusive or contacts
6
7 Safety gate
8 Light curtain

Operating Potentiometer

Poti "Fkt"
< 3 s).
ON
E-Stop
cross fault detection
E-Stop
without
cross fault detection
Adjustment of safety function

Technical Data

Input
Nominal voltage U :
N
Voltage range:
Nominal consumption:
Short-circuit protection:
Overvoltage protection:
Duty-cycle ON button:
Duty-cycle Reset button:
Safety function
Safety mat / safety edge (4)
max. permitted
safety edge contact resistance: 1000 Ω
switching current at short circuit: Typ. 15 mA at U
Light curtains (8)
control current via S12, S22:
Min. voltage on terminals
S12, S22 when relay activated: DC 10 V
Output
Contacts
UG 6980.02
UG 6980.04
The NO contacts can be used for safe braking.
Thermal current I :
th
Safety function
E-Stop (1) (6), Safety gate (2) (7),
Exclusive or contacts (5)
Start up at U :
N
Release delay at U and
N
disconnecting the supply:
Release delay at U and
N
disconnecting S12,S22:
Simultaneity demand:
Two-hand control (3)
Start up at U :
N
Release delay at U and
N
disconnecting the supply:
Release delay at U and
N
disconnecting S12,S22:
Simultaneity demand:
Safety mat (4)
Start up at U :
N
Release delay at U and
N
disconnecting the supply:
Release delay at U and
N
disconnecting S12,S22:
Light curtains (8)
Start up at U :
N
Release delay at U and
N
disconnecting the supply:
Release delay at U and
N
disconnecting S12,S22:
Simultaneity demand:
Switching capacity
to AC 15
to DC 13
contacts 13/14, 23/24:
contacts 43/44, 53/54:
to DC 13
contacts 13/14, 23/24:
Electrical life
at 5 A, AC 230 V cos j = 1:
Zulässige Schalthäufigkeit
UG 6980.02:
UG 6980.04:
Short circuit strength
max. fuse rating:
Mechanical life:
Semiconductor monitoring output
(not safety):
17
DC 24 V
0.8 ... 1.1 U
N
typ. 1.9 W
Internal PTC
Internal VDR
0.1 s < t < 3 s
EIN
> 3 s
N
Typ. 8 mA at U
N
2 NO contacts
4 NO contacts
Max. 8 A
(see quadratic total current limit curve)
< 65 ms
< 40 ms
< 60 ms
< 3 s
< 110 ms
< 40 ms
< 60 ms
< 0,5 s
< 85 ms
< 40 ms
< 60 ms
< 35 ms
< 40 ms
< 25 ms
< 1 s
3 A / AC 230 V IEC/EN 60947-5-1
2 A / DC 24 V IEC/EN 60947-5-1
3 A / DC 24 V IEC/EN 60947-5-1
4 A / DC 24 V at 0.1 Hz
> 1.5 x 10 5 switching cycles
Max. 1800 switching cycles / h
Max. 360 switching cycles / h
6 A gG / gL IEC/EN 60947-5-1
10 x 10 switching cycles
6
max. 50 mA DC 24 V, plus switching
(see current limit curve)
UG 6980 / 08.07.19 en / 214A