Names And Functions Of Indicators On Remote Controller; Automatic Operation - Qlima S5025 Manuel D'utilisation

Swing Button: Press the SWING button to activate the swing feature. Push the button again to stop.
g
Air direction Button: Press this button to change the swing angle of the louver. The swing angle of the
h
louver is 6 for each press. When the louver swings at a certain angle which would affect the cooling and
o
heating effect of the air conditioner, it would automatically change the swing direction. No symbol will
appear in the display area when press this button.
Swing Button(left and right): Press the SWING button to activate the swing feature. Push the button
again to stop.
Timer on Button: Press this button to initiate the auto-on time sequence. Each press will increase the
i
auto-timed setting in 30 minutes increments. When the setting time displays 10Hr, each press will increase
the auto-timed setting 60 minutes increments. To cancel the auto-timed program, continue pressing the
button until 0.0 is displayed.
Timer off Button: Press this button to initiate the auto-off time sequence. Each press will increase the
j
auto-timed setting in 30 minutes increments. When the setting time displays 10Hr, each press will increase
the auto-timed setting 60 minutes increments. To cancel the auto-timed program, continue pressing the
button until 0.0 is displayed.
RESET Button: When you press the recessed RESET button, all current settings are cancelled and the con-
k
trol will return to the initial settings.
Turbo Button / Active Clean button: Push this button on COOL mode, the air conditioner goes into
l
powerful cooling operation. Push again to cancel the TURBO function. Upon pressing this button (> 2
sec) the unit will go into the Active Clean mode. A complete process will be started to clean the internal
side of the evaporator and to reduce the breeding of bacteria. When this function is activated all timer
settings will be cancelled. To stop the Active Clean mode press the button (> 2 sec) again.
LOCK Button: When you press the recessed LOCK button, all current settings are locked in and the remote
m
controller does not accept any operation except that of the LOCK. Press again to cancel the LOCK mode.
LED DISPLAY / FOLLOW ME Button: Press this button to clear the digit display in the air conditioner. The
n
digit display in the air conditioner will reactivate itself automatically after 3 seconds, when no buttons are
being pressed in this period. Press it again to activate it (Not applicable to units without this function).
When pushing more than 2 seconds, the FOLLOW ME function will be activated, pushing more than 2
seconds again to disable.
Low sound button / indoor freezing prevention: Press this button to decrease the indoor sound pres-
o
sure level to 21 dB(A). The indoor unit fan speed is reduced to its lowest level. Upon pressing this button
(> 2 seconds) the unit will go into the freezing prevention mode. The unit will overrule the indoor tem-
perature setting and will set it to approx 8 °C. In this way preventing your home from freezing during
cold periods at the lowest possible energy consumption. When this mode is selected the indoor unit
display will show "FP". This button can only be operated in heating mode. To leave the Home Freezing
Prevention Mode: simply press the button once again.

Names and Functions of indicators on Remote Controller

auto cool dry heat fan
2
1
SET TEMP. TIMER ONOFF
3
4
7
6
sleep lock run
5
4
54 54
Transmission indicator: This transmission indicator lights when remote controller transmits signals to
a
the indoor unit.
Mode display: Displays the current opeartion mode. Including Auto
b
applicable to cooling only models), Fan .
Temp. / Timer display: Displays the temperature setting (17º C ~ 30ºC). When you set the operating
c
mode to FAN, no temperature setting is displayed. And if in the TIMER mode, shows the ON and OFF
settings of the TIMER.
Fan speed display: Displays the selected fan speed, AUTO (no display), LOW
d
fan speed is AUTO when the operating mode is either AUTO or DRY.
ON / OFF display: Displayed by pressing the ON / OFF button. Press the ON / OFF button again to remove.
e
Lock display: Displayed when LOCK mode is activated.
f
Sleep display: Displayed under sleeping operation. Press the SLEEP button again to remove.
g
G
NOTE!
All items are shown in the Fig. 2 for the purpose of clear presentation. But during the actual
operation only the relative functional items are shown on the display panel.
Operating the Remote Controller
Install / Replace Batteries
Use two dry alkaline batteries (AAA/LR03).
Do not use rechargeable batteries.
1. Remove the battery cover on the back of the Remote Control by pulling it according to the arrow
direction shown on the cover.
2. Insert new batteries making sure that the (+) and (-) of battery are installed correctly.
3. Reattach the cover by sliding it back into position.
G
NOTE!
• When the batteries are removed, the remote controller erases all programming. After inserting
new batteries, the remote controller must be reprogrammed.
• When replacing batteries, do not use old batteries or a different type battery. This may cause
the remote controller to malfunction.
• If you do not use the remote controller for several weeks remove the batteries. Otherwise
battery leakage may damage the remote controller.
• The average battery life under normal use is about 6 months.
• Replace the batteries when there is no answering beep from the indoor unit or if the
Transmission Indicator light fails to appear.
• Never mix new and old batteries. Never use different battery types (e.g. alkaline and
manganese dioxide) simultaneously.

AUTOMATIC Operation

When the air conditioner is ready for use (check if unit is plugged in and whether electrical power is availa-
ble), switch on the power and the OPERATION indicator lamp on the display panel of the indoor unit starts
flashing.
1. Use the Mode select button to select AUTO.
2. Push the + or - button to set the desired room temperature.
3. Push the On/off button to start the air conditioner. The OPERATION lamp on the display panel of the
indoor unit lights. The FAN SPEED is automatically controlled.
4. Push the On/off button again to stop the unit operation.
, Cool , Dry , Heat (Not
, MED and HIGH . The
4
55 55