Dry Operation; Timer Operation - Qlima S5025 Manuel D'utilisation

G
NOTE!
• In the AUTO mode, the air conditioner can logically choose the mode COOL, FAN and HEAT by
sensing the difference between the actual ambient room temperature and the set temperature
on the remote controller.
• If the AUTO mode is not comfortable for you , the desired mode can be selected manually.
COOL, HEAT, and FAN ONLY Operation
1. If the AUTO mode is not comfortable, you may manually override the settings by using COOL, DRY,
HEAT (HEAT PUMP units only), or FAN ONLY modes by pressing button b.
2. Push the + or - button (c and d) to set the desired room temperature.
3. Push the Fan button e to select the FAN mode of AUTO, HIGH, MED or LOW.
4. Push the On/off button a. The operation lamp lights and the air conditioner starts to operate per your
settings. Push the On/off button a again to stop this unit operation.
G
NOTE!
The FAN ONLY mode cannot be used to control the temperature. In this mode, only steps 1, 3 and
4 are applicable.

DRY Operation

1. Push the Mode button b to select DRY.
2. Push the + or - button (c and d) to set the desired temperature.
3. Push the On/off button a. The operation lamp lights and the air conditioner starts to operate in the DRY
mode. Push the On/off button a again to stop this unit operation.
G
NOTE!
Due to the difference of the set temperature of the unit and the actual indoor temperature, the
air conditioner when in DRY mode will automatically operate many times without running the
COOL and FAN mode.

TIMER Operation

Push Timer on/off button (i and j) to set the on and off times of the unit. The effective operation time set
by the remote controller for the timer function is limited to a period of between 0.5 and less than 24 hours.
1. To set the STARTING time.
1.1 Push the Timer on button i, then the remote controller display shows ON TIMER, the last set time for
the starting operation and the signal "h" will be shown on the Timer display area. You are now ready
to reset the time to START the operation.
1.2 Push the Timer on button i again to set desired unit start time.
1.3 After setting the Timer on ,there will be half a second delay before the remote controller transmits the
signal to the air conditioner.
2. To set the STOPPING time.
2.1 Push the Timer off button j and the remote controller display will show OFF TIMER and the last set
time for the timer off operation in hours will be shown on the Timer display area. You are now ready
to reset the time of the STOP operation.
2.2 Push the Timer off button j again to set the time you want to stop the operation.
2.3 After setting the Timer off, there will be half a second delay before the remote controller transmits the
signal to the air conditioner.
4
56 56
Example of timer setting
TIMER ON
To start the air conditioner in 6 hours.
1. Press the TIMER ON button, the last setting of starting operation time and the
signal "h" will show on the display area.
Start
2. Press the TIMER ON button to display "6:0h" .
Off
3. Wait for one second and the digital display area will show the temperature again.
6 h
The "TIMER ON" indicator remains on and this function is activated.
Combined timer
TIMER ON OFF
(setting both ON and OFF timers simultaneously)
TIMER OFF --> TIMER ON
On
(On --> Stop --> Start operation)
Stop
On
This feature is useful when you want to stop the air conditioner after you go to bed,
Set
2 h
10 h
and start it again in the morning when you wake up or when you return home.
Example:
To stop the air conditioner 2 hours after setting and start it again 10 hours after setting.
1. Press the TIMER OFF button.
2. Press the TIMER OFF button again to display 2.0h on the TIMER OFF display
3. Press the TIMER ON button
4. Press the TIMER ON button again to display 10h on the TIMER ON display
5. Wait for one second and the digital display area will show the temperature again. The TIMER ON OFF
indicator remains on and this function is activated.
G
NOTE!
• If the same time is set for both START and STOPPING settings, the stopping time will
automatically increase 0.5hr (the set time displays less than 10hr) or one hour (the set time
displays 10hr or more).
• To change the Timer on/off time, just press the corresponding TIMER button and reset the
time.
• The setting time is relative time. That is the time set is based on the delay of the current time.
WARNING
• Keep the remote controller away from all liquids.
• Protect the remote controller from high temperatures and exposure to radiation.
• Keep the indoor receiver out of direct sunlight or the air conditioner may malfunction.
4
57 57