Battery Runtime - Shure Axient AXT100 Mode D'emploi

Émetteur ceinture
Masquer les pouces Voir aussi pour Axient AXT100:
Table des Matières

Publicité

Les langues disponibles

Les langues disponibles

Batteries
The transmitter is powered by a Shure lithium-ion rechargeable battery.
Caution: Turn off the transmitter before changing batteries.
Note: Refer to your battery charger manual for charging instructions.
Press the release buttons to
Main Menu Screen
The main menu screen displays the following transmitter parameters:
1
<Link status>
2
000.000 MHz
00.00
3
4
Locking the Buttons
Lock the buttons of the transmitter to prevent acciden-
tal or unauthorized parameter changes.
Press and hold the ▼ and ▲ buttons for 2 seconds to
lock. Repeat to unlock.
Linking a Transmitter using IR Sync
The IR Sync function forms a Link and sets the frequency between the transmitter and an AXT400 Receiver.
navigate
sync
RF
audio
RF
audio
AXT400
A 470-698 MHz
A
B
A
B
OL
OL
Dual Wireless Receiver
Using Two AXT100 Transmitters for Frequency Diversity
Two AXT100 transmitters can be connected to 2 lavalier microphones using an AXT652 "Y" cable to operate in Frequency Diversity mode with an AXT400 Receiver.
1. Connect the "Y" cable to each transmitter and to the microphones.
2. From the AXT400 menu: Radio > Options > Diversity
3. Use the control wheel to set the mode to FD-Bodypack .
4. Use the IR Sync function to Link a transmitter to each channel of the receiver.
remove the battery
① Channel Name
7
• Linked : Displays Linked receiver channel name
• Unlinked : Not Linked to a receiver, channel
}
6
name reverts to <unlinked>
② Frequency
6
Tuned frequency of the transmitter
|
③ Battery Charge Indicator
5-segment icon indicates battery life
④ Remaining Battery Life
5
Displays remaining battery life in hours and
minutes
Hard Lock Switch
Located inside the battery compartment, this switch
provides an extra level of security against accidental
or unauthorized changes.
When engaged, the power, set, and arrow buttons
cannot be used to change transmitter settings.
The battery must be removed to access the switch.
1. Access the IR Sync function in the AXT400 receiver menu: Tx
2. Align the IR Sync ports of the transmitter and the receiver. The red IR Sync LED on the receiver IR port
power
navigate
control
monitor
clip
push
enter
1
2
exit
will illuminate to indicate correct alignment. Press Sync .
push
3. The receiver display indicates if the IR Sync is successful. Check the transmitter alignment and select
Retry if a failure occurs.
4. The transmitter device ID will be shown in the receiver Tx menu and the receiver channel name and fre-
quency will be shown on the transmitter display, indicating a successful IR sync.

Battery Runtime

Battery runtime varies according to the transmitter's operating mode. High power
settings will reduce battery runtime.
Remaining battery runtime is shown on the display in hours and minutes (accurate
to within 15 minutes).
The times shown in the table represent a battery with a minimum of 5 charge
cycles, fully charged, at 100% health.
RF Power (mW)
Runtime ShowLink Enabled
(hours/minutes)
10
7:30
100
5:35
⑤ ShowLink Icon
⑥ Audio Meter
⑦ Control Lock Icon
Power-on RF Mute
Power-on RF mute prevents transmission of audio
when powering on the transmitter.
With the transmitter turned off, press and hold both
the ▼ button and the SET button, and then press and
hold the Power button.
After power-on, an RF Muted message indicates that
the transmitter is in RF Mute mode.
Note: RF Mute mode persists through power cycles of
the transmitter.
2
Runtime Without
ShowLink
(hours/minutes)
8:00
6:05
Indicates remote control of transmitter via
ShowLink is possible
Indicates the audio signal level
Displayed when buttons are locked

Publicité

Table des Matières
loading

Table des Matières