Language Choice; Alarm Indications - Cardin Elettronica SLX 324 Mode D'emploi

• Set the main operating parameters (e.g. installation right/left) in the options menu.
• If you have safety devices working with 8.2k contacts select the correct setting from the safety device menu.
• Before programming the gate travel distances select the correct motor in the "Motion" menu.
OPTIONS
SAFETY DEVICES
MOTION
Arrow
DISPLAY
to
CALENDAR
scroll
REMOTE
"PROG/OK"
to confirm
SET TIME
08:00
SET DATE
"PROG/OK"
23-12-13 to change
the value
SET EVENTS
SET TIME
08:00
"PROG/OK"
SET DATE
to change
23-12-13
the value
SET EVENTS
SET TIME
08:00
SET DATE
23-12-13
"PROG/OK"
SET EVENTS
to confirm
EVENT 0
SET DATE
MO-SU 08-10 TA 1
23-12-13
EVENT 1
SET EVENTS
MO-SU 08-10 TA 1
EVENT 2
EVENTS: ON/OFF
MO-FR 10-08 TA 0
EXIT
Note: 6
SET EVENTS
"PROG/OK"
to return to the
EVENTS: ON/OFF
calender menu
EXIT
Note:
6) Events On/Off:
Setting one of the radio channels to 'events
on/off' will allow you to activate/deactivate
the events via radio control. Activation will be
indicated by the warning light and indicator
light flashing for 6 seconds. Deactivation
will be indicated by the lights flashing for 3
seconds.
7) Encoding:
Before changing the encoding type you must
substitute the memory module, changing from
S4XX to S500 and viceversa
switched off.
Operational indications
Pause time programming or
PAUSE
pause
TB FI TA TD
reclosing (if activated)
FS CP TC TAL
AUTO PROG Automatic programming
TB FI TA TD
under way
FS CP TC TAL
OPENING
TB FI TA TD
Opening stage
FS CP TC TAL
STOP OPENING
Block during opening
TB FI TA TD
FS CP TC TAL
CLOSING
TB FI TA TD Closing stage
FS CP TC TAL
STOP CLOSING
TB FI TA TD Block during closing
FS CP TC TAL
OPTIONS
SAFETY DEVICES
MOTION
Arrow
Arrow
DISPLAY
to scroll
to exit
CALENDAR
REMOTE
"PROG/OK"
to confirm "PROG/OK"
to toggle the
ENCODING: S4XX
value between
MEMORISE
S4XX & S500
CANCEL
Note: 7
CLEAR ALL MEMORY
CHANNEL FUNCTION
EXIT
ENCODING: S4XX
"PROG/OK"
MEMORISE
to confirm
CANCEL
CLEAR ALL MEMORY
CHANNEL FUNCTION
EXIT
ENCODING: S4XX
MEMORISE
"PROG/OK"
CANCEL
to confirm
CLEAR ALL MEMORY
CHANNEL FUNCTION
EXIT
ENCODING: S4XX
MEMORISE
CANCEL
"PROG/OK"
CLEAR ALL MEMORY
to confirm
CHANNEL FUNCTION
EXIT
ENCODING: S4XX
MEMORISE
CANCEL
CLEAR ALL MEMORY
"PROG/OK"
CHANNEL FUNCTION
to confirm
EXIT
ENCODING: S4XX
"PROG/OK"
MEMORISE
to return to
CANCEL
the remote
menu
CLEAR ALL MEMORY
CHANNEL FUNCTION
EXIT
PROGRAM
TB FI TA TD
FS CP TC TAL
TB FI TA TD
FS CP TC TAL
OUT OF POS
STOP PROG
TB FI TA TD
FS CP TC TAL
AUTO PROG
with the power
TB FI TA TD
FS CP TC TAL
SAFETY ERROR
TB FI TA TD
FS CP TC TAL
for automatic
ERROR MOT
TB FI TA TD
FS CP TC TAL
ERROR ENC
TB FI TA TD
FS CP TC TAL
ERROR DIR
TB FI TA TD
FS CP TC TAL
ERROR SENS
TB FI TA TD
FS CP TC TAL
ACT. SAFETY EDGE
TB FI TA TD
FS CP TC TAL
ACTIVE SENSOR

Language choice:

• Press the right and left buttons
simultaneously to enter the
language submenu.
• Press the right and left buttons
to change the language: Italian
to English.
• Press the "PROG/OK" button
to con rm the choice.
MEMORISE
PRESS the
[Nr...]
transmitter
* * * * * * * * * * * * * * *
channel
[AB--]
* *
to memorise
* ACTIVATION 1
*
* *
* * * * * * * * * * * * * * *
CANCEL
PRESS the
[Nr...]
transmitter
* * * * * * * * * * * * * * *
channel
[AB--]
* * to memorise
* ACTIVATION 1
*
* *
* * * * * * * * * * * * * * *
EXIT
* * * * * * * * * * * * * * *
CANCEL
* *
* ALL MEMORY ? *
PRESS ok to
* * * * * * * * * * * * * * * cancel all
memory
OK
or press exit
CHANNEL A Note: 8
channel function A
CHANNEL B
"PROG/OK"
to change
channel function B
the value
CHANNEL C
channel function C
CHANNEL D
channel function D
EXIT

Alarm indications

Flashing on the display. You have to enter the programming mode to program the system.
During normal operation it indicates that the "automatic repositioning" procedure is about to
take place. In this case any commands received (TA, TC, TAL or TD) will automatically start
this procedure.
This happens when an N.C. contact is activated (FI, FS, CP) during encoder programming or
automatic repositioning. Once the passive state of the security devices has been reset the gate
will start moving again automatically. It also happens if a blackout occurs during programming.
Safety device test error. Check the condition of the safety devices and make sure that the
alarm cuts in when an obstacle interferes with the beam (indication white characters on a black
background). In case of anomalies replace the damaged safety device or bridge the contact
and deactivate the safety test (option menu).
This occurs when the programmer sends a command to the motor and nothing happens (motor
doesn't move). Check the Faston connections of the motor and the condition of the fuses "F3",
"F4" and then give another opening or closing command. If the motor still doesn't move you are
faced with either a mechanical problem or a problem with the programmer.
Encoder count error. If this error occurs during normal motor operation it means that there is a
problem with the encoder signal. Check the relative connections and carry out automatic
repositioning.
Encoder direction error. The gate movement direction is different from the encoder setting (eg.
the gate moves in the closing direction while the program is carrying out the opening stage).
Check motor power supply connections.
Current sensor error. When the gate is not moving this symbol means there is a problem with
the current sensor.
When the safety edge intervenes the gate will automatically invert for a few moments, both in the
closing as well as the opening direction, to free the obstacle it will then stop for 3 minutes and
then continue moving in the original direction after a 10 second pre ashing period has elapsed.
When the sensor intervenes the gate will automatically invert for a few moments, both in the
closing as well as the opening direction, to free the obstacle it will then stop for 3 minutes and
then continue moving in the original direction after a 10 second pre ashing period has elapsed.
19
PROGRAM
ITALIANO
TB FI TA TD
FRANÇAIS
FS CP TC TAL
ENGLISH
NEDERLANDS
DEUTSCH
00.000.007
ESPAÑOL
07-06-13 15.35
"PROG/OK" to confirm
press both arrows
simultaneously to enter
the language submenu
MEMORISE MEMORISE
PRESS the
[Nr...]
the same
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * *
transmitter
[AB--]
channel
* * *
* ACTIVATION 2 CODE
again
* *
MEMORISED
* * *
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * *
CANCEL CANCEL
PRESS the
[Nr...]
the same
* * * * * * * * * * * * * * * transmitter * * * * * * * * * * * * * * *
[AB--]
channel
* * *
* ACTIVATION 2 CODE
again
* *
CANCELLED
* * *
* * * * * * * * * * * * * * *
* * * * * * * * * * * * * * *
8) Channel functions
Each radio control channel can
* * * * * * * * * * * * * * *
"A","B","C","D"
be
* CANCELLING
*
* * * * * * * * * * * * * * *
of 7 available functions:
- TD sequential command
- TAL limited opening
TA open
-
- TC close
- Block
CH2 second radio channel
-
- events on/off
[Nr...]
[AB--]
*
*
*
[Nr...]
[AB--]
*
*
*
set to one