Publicité
Les langues disponibles
Les langues disponibles
IMPORTANT: Do not tighten bolts until step 3 is complete.
1
A Open HARDWARE FOR STEP 1.
B Attach LEFT CONSOLE MAST (1) to BASE FRAME (2)
using 4 BOLTS (A), 4 SPRING WASHERS (B) and 4
T50
FLAT WASHERS (C). Tighten to 30 Nm / 22 lb-ft.
T70
C
Attach LEAD WIRE (3) to CONSOLE CABLE (4) and pull lead
wire through RIGHT CONSOLE MAST (5). After pulling the lead
wire through the mast, the top of the console cable should be
located at the top of the mast. Detach and discard lead wire.
D Repeat step B on other side.
NOTE: Be careful not to pinch any wires while attaching the right
console mast.
Hardware For Step 1
Description
Qty
A
Bolt
8
B
Spring Washer
8
C
Flat Washer
8
1
C
B
A
2
80
MXR20_AG_Treadmills_r1_1_B.indd 80-81
MXR20_AG_Treadmills_r1_1_B.indd 80-81
A Open HARDWARE FOR STEP 2.
2
B Place CONSOLE MAST BOOTS (6) on top of CONSOLE MASTS (1 & 5).
C
Connect the CONSOLE CABLES (4), discard the wire ties,
and tuck the cables inside the CONSOLE MASTS (1 & 5) and
slide CONSOLE BASE (7) into CONSOLE MASTS (1 & 5).
T50
T70
D Attach CONSOLE BASE (7) to CONSOLE MASTS (1 &
5) using 4 BOLTS (E), 4 SPRING WASHERS (F) and 4
FLAT WASHERS (G). Tighten to 20 Nm / 15 lb-ft.
NOTE: Be careful not to pinch any wires while attaching the console base.
Hardware For Step 2
Description
Qty
E
Bolt
4
F
Spring Washer
4
3
G
Flat Washer
4
4
7
6
5
4
4
1
A Open HARDWARE FOR STEP 3.
3
B Place HANDLEBAR SLEEVES (8) on top of CONSOLE MASTS (1 & 5).
C
Connect the CONSOLE CABLES (4) and tuck the
cables inside the CONSOLE MASTS (1 & 5).
T50
D Attach HANDLEBAR (9) to CONSOLE MASTS
T70
(1 & 5) using 2 BOLTS (H) and 4 BOLTS
(I). Tighten to 15 Nm / 11 lb-ft.
E
Tighten all bolts from steps 1–3.
Note: Be careful not to pinch any wires while attaching the handlebar.
Hardware For Step 3
Description
Qty
H
Bolt
2
I
Bolt
4
4
G
E
F
5
1
4
A Insert 4 HANDLEBAR CAPS (10) into HANDLEBAR (9).
4
B Slide OUTSIDE BASE FRAME COVERS (11) over bolts at the bottom of
the CONSOLE MASTS (1 & 5).
C
T50 only: Open HARDWARE FOR STEP 4.
T50
D T50 only: Attach INSIDE BASE FRAME COVERS (12) using 4 SCREWS (J).
T70
H
8
9
4
1
J
11
12
I
5
1
11
Hardware For Step 4 (T50 only)
Description
Qty
J
Screw
4
10
5
T50
5
T70
81
12/29/20 10:50 AM
12/29/20 10:50 AM
Publicité
