Matrix TF30 Instructions De Montage page 39

IMPORTANT: Do not tighten bolts until step 3 is complete.
1
A Open HARDWARE FOR STEP 1.
B Attach LEFT CONSOLE MAST (1) to BASE FRAME (2) using 4
TF30 BOLTS (A), 4 SPRING WASHERS (B) and 4 FLAT WASHERS (C)
from the side and 1 BOLT (D), 1 SPRING WASHER (B) and 1
TF50
FLAT WASHER (C) from the rear. Tighten to 20 Nm / 15 lb-ft.
C Attach LEAD WIRE (3) to CONSOLE CABLE (4) and pull lead
wire through RIGHT CONSOLE MAST (5). After pulling the lead
wire through the mast, the top of the console cable should be
located at the top of the mast. Detach and discard lead wire.
D Repeat step B on other side.
NOTE: Be careful not to pinch any wires while attaching the right
console mast.
Hardware For Step 1
Description Qty
3
A Bolt 8
B Spring Washer 10
C Flat Washer 10
4
D Bolt 2
5
4
1
D
C
B
A
2
76
MXR20_AG_Treadmills_r1_1_B.indd 76-77 MXR20_AG_Treadmills_r1_1_B.indd 76-77
A Open HARDWARE FOR STEP 2.
2
B Place CONSOLE MAST BOOTS (6) on top of CONSOLE MASTS (1 & 5).
C Connect the CONSOLE CABLES (4) , discard the wire ties, and tuck the cables inside
the CONSOLE MASTS (1 & 5) and slide CONSOLE BASE (7) into console masts.
TF30
D Attach CONSOLE BASE (7) to CONSOLE MASTS (1 & 5) using 4 BOLTS (E), 4
SPRING WASHERS (F) and 4 FLAT WASHERS (G). Tighten to 20 Nm / 15 lb-ft.
TF50
NOTE: Be careful not to pinch any wires while attaching the console base.
Hardware For Step 2
Description Qty
E Bolt 4
F Spring Washer 4
G Flat Washer 4
7
6
4
E
1
A Open HARDWARE FOR STEP 3.
3
B Place HANDLEBAR SLEEVES (8) on top of CONSOLE MASTS (1 & 5).
C Connect the CONSOLE CABLES (4) and tuck the
cables inside the CONSOLE MASTS (1 & 5).
TF30
D Attach HANDLEBAR (9) to CONSOLE MASTS
(1 & 5) using 2 BOLTS (H) and 4 BOLTS
TF50
(I). Tighten to 15 Nm / 11 lb-ft.
E Tighten all bolts from steps 1–3.
Note: Be careful not to pinch any wires while attaching the handlebar.
Hardware For Step 3
Description Qty
H Bolt 2
I Bolt 4
4
G
F
5 1 5
4
A Open HARDWARE FOR STEP 4.
4
B Insert 4 HANDLEBAR CAPS (10)
into HANDLEBAR (9).
C Attach BASE FRAME COVERS (11) to the
TF30 BASE FRAME (2) using 2 SCREWS (J) from the
inside and 2 SCREWS (K) from the outside.
TF50
D Repeat on other side.
H 8 9 4
10
11 J
I
K 2
Hardware For Step 4
Description Qty
J Screw (10 mm) 4
K Screw (30 mm) 4
77
12/29/20 10:50 AM 12/29/20 10:50 AM