Table des Matières
Publicité
PROGRAMMING
Perform a cancellation procedure before starting programming (see next paragraph). The programming
phase can only be performed after the above.
CANCELLATION PROCEDURE
Sensors:
Press the cancel pushbutton for at least 5 seconds (see figs. 4-5).
Base:
Press the programming pushbutton until the red led (DL9) illuminates, flashing first and then
remaining permanently lit, and then turns off. Release the pushbutton when the led turns off.
PROGRAMMING PROCEDURE
Programming is performed after wiring the base to the board of the automation and the sensor/s to the
edge/s.
1. Insert the batteries in the TWC sensor, observing the correct polarity.
2. Set a code on the rack of dip-switches present on the TWM base board. This ensures that the system
can operate also in the vicinity of other wireless systems, which obviously must have different codes.
Use dip-switches 1-2-3 for settings of up to 8 combinations. Dip-switch 4 is used to select the type of
sensitive edge (Dip 4 OFF sensitive edge NOT resistive, DIP 4 ON for resistive sensitive edge).
Note: Variations to the dip-switch configuration vary the transmission frequency between the
base and relative sensors (to remedy possible interference between different installations). Each
time you change the frequency using dip switches 1-2-3, you will need to repeat the "DELETION
PROCEDURE" and "PROGRAMMING PROCEDURE".
3. Power up the automation. All leds must be off. If one or more of the green leds are lit, go to the section
"CANCELLATION PROCEDURE".
4. Press the programming key on the TWM base for approx. 3 seconds until the "fixed edge" led (DL1)
flashes. Go to point 6 if this sensor is not to be installed.
5. Press the programming pushbutton on the TWC sensor to be assigned with the fixed edge function
(sensitive edge active on opening). The "fixed edge" led (DL1) remains permanently lit as soon as sen-
sor programming is completed. Release the key on the sensor.
6. Press the programming pushbutton on the base once. The led associated with the "mobile edge" (DL2)
now starts flashing.
7. Press the programming pushbutton on the TWC sensor to be assigned with the mobile edge function
(sensitive edge active on closure). The "mobile edge" led (DL2) remains permanently lit as soon as sen-
sor programming is completed. Release the key on the sensor.
8. Press the programming pushbutton on the base for three seconds. The leds of the programmed sensors
turn off for approx. 1 second. Release the pushbutton when they light up again. Programming is now
complete.
Note: skip points 6 and 7 if programming one sensitive edge only, used as a fixed edge (sensitive
edge active on opening).
TABLE 1: WIRING OF TWM BASE TO TAU CONTROL UNIT
TWM (terminal nr.)
D703M (terminal nr.)
D704M / D705M (terminal nr.)
D747M (terminal nr.)
D750M (terminal nr.)
D760M (terminal nr.)
K120M (terminal nr.)
K122M (terminal nr.)
K123M (terminal nr.)
K125M (terminal nr.)
K570M (terminal nr.)
K580M (terminal nr.)
N.U. =
Not Used
1
2
3
4
30
29
N.U.
25
26
25
N.U.
27
1
2
N.U.
7
27
26
N.U.
23
27
26
N.U.
23
8
9
N.U.
14
1
2
N.U.
7
3
4
N.U.
9
8
9
N.U.
14
24
23
N.U.
20
14
13
N.U.
17
TAU-WIRELESS
5
6
7
8
16
N.U. N.U.
17
17
N.U. N.U.
18
18
N.U. N.U. 16/19
18
N.U. N.U.
15
18
N.U. N.U.
15
3
N.U. N.U.
1
12
N.U. N.U.
9
14
N.U. N.U.
11
3
N.U. N.U.
1
13
N.U. N.U.
14
10
N.U. N.U.
11
Jump
9
J2
J4
18
no
no
16
no
no
15
yes
yes
17
no
no
17
no
no
2
yes
yes
10
yes
yes
12
yes
yes
2
yes
yes
15
no
no
12
no
no
9
Publicité
Table des Matières
