Limits Of Use; Technical Data; General Data; Electrical Data - pizzato FG Serie Mode D'emploi

- The utilization implies knowledge of and compliance with following standards:
EN 60947-5-3, EN ISO 13849-1, EN 62061, EN 60204-1, EN ISO 14119,
EN ISO 12100.

6.7 Limits of use

- Use the device following the instructions, complying with its operation limits and the
standards in force.
- The devices have specific application limits (min. and max. ambient temperature,
mechanical endurance, IP protection degree, etc.) These limitations are met by the
device only if considered individually and not as combined with each other.
- The manufacturer's liability is to be excluded in the following cases:
1) Use not conforming to the intended purpose;
2) Failure to adhere to these instructions or regulations in force;
3) Fitting operations not carried out by qualified and authorized personnel;
4) Omission of functional tests.
- For the cases listed below, before proceeding with the installation contact our
technical assistance service (see paragraph SUPPORT):
a) In nuclear power stations, trains, airplanes, cars, incinerators, medical devices
or any application where the safety of two or more persons depend on the correct
operation of the device;
b) Applications not contemplated in this instruction manual.
- Permanent application of maximum holding force F
7 MARKINGS
The outside of the device is provided with external marking positioned in a visible
place. Marking includes:
- Producer trademark
- Product code
- Batch number and date of manufacture. Example: A19 FG1-123456. The batch's first
letter refers to the month of manufacture (A=January, B=February, etc.). The second
and third letters refer to the year of manufacture (19 = 2019, 20 = 2020, etc...).

8 TECHNICAL DATA

8.1 Housing
Metal head and housing, baked powder coating.
Three threaded conduit entries:
Protection degree:

8.2 General data

The device can be used in applications with an interlocking function, up to the
maximum of the following functional safety levels according to EN ISO 13849-1 and
EN 62061:
- With one device applied to the guard, with no supervisory logic unit:
- With one device applied to the guard, with an adequate supervisory logic unit
and with the possibility of excluding the fault in the mechanical part actuating the
device:
- With two devices applied to the same guard and with an adequate supervisory logic
unit:
Attention: Any connection in series of the electrical safety contacts of two or
more devices decreases the system's self-monitoring capacity, see ISO/TR 24119.
Interlock with mechanical lock, coded:
Coding level:
Safety parameters:
B :
10D
Mission time:
Ambient temperature:
Storage temperature:
Max. actuation frequency:
Mechanical endurance:
Max. actuation speed:
Min. actuation speed:
Maximum force before breakage F
1max
Max. holding force F :
Zh
Released actuator extraction force:

8.3 Electrical data

8.3.1 Versions without connector
Thermal current (I ):
th
Rated insulation voltage (U ):
i
Rated impulse withstand voltage (U
imp
Conditional short circuit current:
Protection against short circuits:
Pollution degree:
8.3.2 Versions with M23 connector, 12-pole
Thermal current (I ):
th
Rated insulation voltage (U ):
i
Protection against short circuits: fuse
Pollution degree:
8.3.3 Versions with M12 connector, 12-pole
Thermal current (I ):
th
Rated insulation voltage (U ):
i
Protection against short circuits:
Pollution degree:
8.3.4 Electrical data of the solenoid
Supply voltage:
Items FG 6••D•3•:
Items FG 6••D•0•:
Items FG 6••D•1•:
Items FG 6••D•2•:
Duty cycle:
is not permitted.
zh
M20x1.5
IP67 acc. to EN 60529
with cable gland of equal
or higher protection degree
category 1, PL c, SIL 1;
category 3, PL d, SIL 2;
category 4, PL e, SIL 3.
type 2 acc. to EN ISO 14119
Low acc. to EN ISO 14119
5,000,000 for NC contacts
20 years
-25°C ... +60°C
-40°C ... +80°C
600 operating cycles/hour
1 million operating cycles
0.5 m/s
1 mm/s
: 2800 N acc. to EN ISO 14119
2150 N acc. to EN ISO 14119
30 N
10 A
400 Vac 300 Vdc
): 6 kV
1000 A acc. to EN 60947-5-1
type gG fuse 10 A 500 V
3
8 A
250 Vac 300 Vdc
8 A 500 V type gG
3
1.5 A
30 Vac 36 Vdc
type gG fuse 1.5 A
3
12 Vdc -15% +20%
24 Vac/dc -10% +10%
120 Vac/dc -15% +10%
230 Vac -15% +10%
100% ED
Solenoid protection 12 V:
Solenoid protection 24 V:
Solenoid protection 120 V:
Solenoid protection 230 V:
Solenoid consumption:
8.3.5 Utilization categories
Versions without connector:
Alternating current: AC-15 (50÷60 Hz)
Ue (V) 120
Ie (A) 6
Direct current: DC-13
Ue (V) 24
Ie (A) 3
Versions with M23 connector, 12-pole:
Alternating current: AC-15 (50÷60 Hz)
Ue (V) 120
Ie (A) 6
Direct current: DC-13
Ue (V) 24
Ie (A) 3
Versions with M12 connector, 12-pole:
Alternating current: AC-15 (50÷60 Hz)
Ue (V) 24
Ie (A) 1.5
Direct current: DC-13
Ue (V) 24
Ie (A) 1.5

8.4 Compliance with standards

IEC 60947-5-1, EN 60947-5-1, EN 60947-1, IEC 60204-1, EN 60204-1, EN ISO 14119,
EN ISO 12100, IEC 60529, EN 60529, EN 61000-6-2, EN 61000-6-3, EN 50581,
BG-GS-ET-15, UL 508, CSA 22.2 N. 14.
8.5 Compliance with the requirements of:
Machinery Directive 2006/42/EC, EMC Directive 2014/30/EU, RoHS Directive
2011/65/EU.
9 SPECIAL VERSIONS ON REQUEST
Special versions of the device are available on request.
The special versions may differ substantially from the indications in this instruction
sheet.
The installer must ensure that he has received written information from the support
service regarding installation and use of the special version requested.
10 DISPOSAL
At the end of service life product must be disposed of properly, according to the
rules in force in the country in which the disposal takes place.
11 SUPPORT
The device can be used for safeguarding people's physical safety, therefore in case of
any doubt concerning installation or operation methods, always contact our technical
support service:
Pizzato Elettrica Srl
Via Torino, 1 - 36063 Marostica (VI) - ITALY
Telephone +39.0424.470.930
E-mail tech@pizzato.com
www.pizzato.com
Our support service provides assistance in Italian and English.

12 EC CONFORMITY DECLARATION

I, the undersigned, as a representative of the following manufacturer:
Pizzato Elettrica Srl - Via Torino, 1 - 36063 Marostica (VI) – ITALY
hereby declare that the product is in conformity with whatever prescribed by the 2006/42/
EC Machine Directive. The complete version of the present conformity declaration is
available on our website www.pizzato.com
Marco Pizzato
DISCLAIMER:
Subject to modifications without prior notice and errors excepted. The data given in this sheet are accurately
checked and refer to typical mass production values. The device descriptions and its applications, the
fields of application, the external control details, as well as information on installation and operation, are
provided to the best of our knowledge. This does not in any way mean that the characteristics described
may entail legal liabilities extending beyond the "General Terms of Sale", as stated in the Pizzato Elettrica
general catalogue. Customers/users are not absolved from the obligation to read and understand our
information and recommendations and pertinent technical standards, before using the products for their
own purposes. Taking into account the great variety of applications and possible connections of the device,
the examples and diagrams given in the present manual are to be considered as merely descriptive; the
user is deemed responsible for checking that the specific application of the device complies with current
standards. This document is a translation of the original instructions. In case of discrepancy between
the present sheet and the original copy, the Italian version shall prevail. All rights to the contents of this
publication are reserved in accordance with current legislation on the protection of intellectual property. The
reproduction, publication, distribution and modification, total or partial, of all or part of the original material
contained therein (including, but not limited to, texts, images, graphics), whether on paper or in electronic
form, are expressly prohibited without written permission from Pizzato Elettrica Srl.
All rights reserved. © 2021 Copyright Pizzato Elettrica
8/24
type gG fuse 1 A
type gG fuse 0.5 A
fuse 315 mA, delayed
fuse 315 mA, delayed
9 VA
250 400
5 3
125 250
0.7 0.4
250
5
125 250
0.7 0.4