Table des Matières
Publicité
PIECES AILES
(W1) Aile avec aileron et AF montés ......................................... (G/D) 1 de chaque
(W2) Trappe servo aileron ........................................................ (G/D) 1 de chaque
(W3) Vis à bois 2,2x12mm, fixation trappes d'ailerons ........................................8
(W4) Guignol d'aileron fibre de verre............................................................ 2 sets
(W5) Tringlerie d'aileron avec chape métal M2 et écrou M2 ........................ 2 sets
(W6) Clé d'aile (tube carbone Ø25x700mm) ........................................................1
(W7) Vis fixation d'aile (plastique M6x20mm) ......................................................2
PIECES PROFONDEUR
(E1) Stab pendulaire ................................................................. (G/D) 1 de chaque
(E2) Clé de stab principale, tube laiton Ø9x380mm .............................................1
(E3) Clé de stab secondaire, tube laiton Ø5x130mm ...........................................1
(E4) Vis à bois 3x15mm, fixation stab ..................................................................2
(E5) Couple arrière platine servo de profondeur CTP 3mm .................................1
(E6) Couple supérieur platine servo de profondeur CTP 3mm .............................1
(E7) Platine servo de profondeur CTP 3mm .........................................................1
(E8) Bras guignol pendulaire fibre de verre 2mm.................... (G/D) 1 de chaque
(E9) Plancher guignol pendulaire fibre de verre 2mm .........................................1
(E10) Renfort vertical guignol pendulaire fibre de verre 2mm ............................1
(E11) Entretoise circulaire guignol pendulaire fibre de verre 2mm .......................
................................................................................................... (G/D) 1 de chaque
(E12) Tringlerie de profondeur tige filetée M3 .....................................................1
(E13) Chape à rotule M3 avec écrou et rondelle............................................1 set
(E14) Chape métal M3 avec écrou ................................................................. 1 set
PIECES DIRECTION
(R1) Volet de dérive .............................................................................................. 1
(R2) Guignol de direction fibre de verre ...............................................................1
(R3) Chape M2 avec embout pour câble et écrou M2 .................................. 4 sets
(R4) Câble de direction acier, rouleau de 3 mètres ..............................................1
(R5) Tube de sertissage pour câble acier ............................................................4
WINGS PARTS
(W1) Wing with aileron and speedbrake installed ...............................(L/R) 1 each
(W2) Aileron servo hatch ....................................................................(L/R) 1 each
(W3) Self-tapping screw 2.2x12mm, aileron hatch attachment ............................8
(W4) Aileron control horn, fiberglass ............................................................ 2 sets
(W5) Aileron linkage with M2 metal clevis and M2 nut ................................. 2 sets
(W6) Wing joiner (carbon tube Ø25x700mm) .......................................................1
(W7) Screw for wing attachment (nylon M6x20mm) .............................................2
ELEVATOR PARTS
(E1) Floating elevator .........................................................................(L/R) 1 each
(E2) Main stab joiner, brass tube Ø9x380mm ......................................................1
(E3) Secondary stab joiner, brass tube Ø5x130mm ............................................1
(E4) Self-tapping screw 3x15mm, stab attachment .............................................2
(E5) Rear former for elevator servo tray, plywood 3mm ......................................1
(E6) Upper former for elevator servo tray, plywood 3mm ....................................1
(E7) Elevator servo tray, plywood 3mm ................................................................1
(E8) Elevator bellcrank arm, fiberglass 2mm .....................................(L/R) 1 each
(E9) Elevator bellcrank floor, fiberglass 2mm .......................................................1
(E10) Elevator bellcrank arm vertical reinforcement, fiberglass 2mm .................1
(E11) Elevator bellcrank arm circular spacer, fiberglass 2mm ...........(L/R) 1 each
(E12) Elevator linkage, threaded wire M3 ............................................................1
(E13) M3 ball link with nut and washer ........................................................... 1 set
(E14) M3 metal clevis with nut ........................................................................ 1 set
RUDDER PARTS
(R1) Rudder........................................................................................................... 1
(R2) Rudder control horn, fiberglass ....................................................................1
(R3) M2 clevis with cable coupler and M2 nut .............................................. 4 sets
(R4) Steel rudder cable, 3-meter roll....................................................................1
(R5) Press fitting for steel cable ...........................................................................4
SCHLEICHER
Ka 6E
CONTENU DU KIT
KIT CONTENT
Notice Ecotop - Page 7 - Ka 6E 5.0m ARF
PIECES FUSELAGE
(F1) Fuselage en fibre de verre, peint .................................................................1
(F2) Fourreau clé d'aile en fibre de verre (dans fuselage, à coller) ....................1
(F3) Verrière montée sur son baquet avec aimants de fixation intégrés .............1
(F4) Ecrous à griffes M4 fixation moteur .............................................................4
(F5) Couple moteur CTP 5 mm .............................................................................. 1
(F6) Platine radio et accus CTP 3mm ...................................................................1
(F7) Couple avant platine servo de direction CTP 3mm .......................................1
(F8) Platine servo de direction CTP 6mm .............................................................1
(F9) Couple arrière platine servo de direction CTP 3mm .....................................1
(F10) Etambot fixe CTP 3mm ................................................................................ 1
(F11) Vis TF M3x12mm pour fixation étambot .....................................................5
(F12) Ecrous à griffes M3 pour fixation étambot ..................................................5
(F13) Etambot mobile CTP 3mm avec paliers et axe carbone dérive ...........1 set
PIECES TRAIN D'ATTERRISSAGE
(LG1) Couple avant support de train, fibre de verre 5mm ...................................1
(LG2) Couple arrière support de train, fibre de verre 5mm .................................1
(LG3) Flancs support de train, fibre de verre 5mm ..............................................2
(LG4) Partie supérieure support de train, fibre de verre 5mm ............................1
(LG5) Roue Ø89mm .............................................................................................. 1
(LG6) Axe de roue+bagues d'arrêt+écrou+rondelles ..................................1 set
(LG7) Gabarit découpe passage du train CTP 3mm ..............................................1
DIVERS
(D1) Manuel de montage ...................................................................................... 1
FUSELAGE PARTS
(F1) Fiberglass fuselage, painted ........................................................................1
(F2) Fiberglass wing tube (inside the fuselage, to be glued) ...............................1
(F3) Canopy installed on its frame with integrated magnets ................................1
(F4) M4 tiger nut for motor attachment ...............................................................4
(F5) Motor mount, plywood 5 mm ........................................................................1
(F6) Radio and battery packs tray, plywood 3mm ................................................1
(F7) Front former for rudder servo tray, plywood 3mm .......................................1
(F8) Rudder servo tray, plywood 6mm ..................................................................1
(F9) Rear former for rudder servo tray, plywood 3mm ........................................1
(F10) Fix rudder post, plywwod 3mm ...................................................................1
(F11) Countersunk head screw M3x12mm for post attachment ..........................5
(F12) M3 tiger nut for post attachment ................................................................5
(F13) Mobile rudder post, plywood 3mm with bearings and carbon axle .....1 set
LANDING GEAR PARTS
(LG1) Front former for LG support, fiberglass 5mm .............................................1
(LG2) Rear former for LG support, fiberglass 5mm ..............................................1
(LG3) Side former for LG support, fiberglass 5mm ...............................................2
(LG4) Upper part for LG support, fiberglass 5mm ................................................1
(LG5) 3.5' wheel .................................................................................................... 1
(LG6) Wheel axle+stopper+nut+washers ..................................................... 1 set
(LG7) Cutting jig for the wheel, plywood3mm ........................................................1
VARIOUS
(D1) Construction manual ..................................................................................... 1
Publicité
Table des Matières
