Andis BGRC Mode D'emploi page 3

Model BGR+ With Battery Use
1. Models BGRC/BGR+ will run on an average of 3800 SPM with the battery pack attached.
2. Models BGRC/BGR+ can be used with either the cord pack or the battery.
READ THE FOLLOWING BEFORE CHARGING THIS CLIPPER
1. Remove the charger from the carton and plug into an AC
outlet as identified on charger unit and on carton.
2. Place the Andis Model BGR+ Cordless Clipper in the form
fitting pocket in the charger base. Note that the battery pack is
fitted with a slot to align properly with the charger. Once the
battery and charger are aligned, press the battery pack firmly
into the charger until it rests at the bottom of the pocket. You
may hear a click as the charging contacts engage this is nor-
mal. The battery pack may be charged while on the clipper, or
separately. Push the battery release button (Diagram B) on
the clipper, and pull straight out to remove the battery.
NOTE: The battery pack is designed to run the clipper for
about one hour. A clean, sharp, well-oiled blade will provide
the best run time.
3. Before initial use battery pack must be charged for a
minimum of one hour.
4. The charger base has two indicator lights: Below is a
description of the Sensacharge light sequences: (Diagram C)
Continuous Green Light (Fast Charge)- Charger will fully
charge battery pack in less than one hour.
Rapid Green Blinking Light (Charging Complete)- Battery
pack is fully charged.
Long Green Blinking Light ("Refresh") Charger is draining
battery pack in preparation for fast charge. Please reference
the section "Use of the Refresh Feature" on page 6 for an
explanation.
Short Green Blinking Light-
a) With Continuous Red Light (Charge Standby)- Battery
pack is trickle charging because it is either too hot or too
cold to accept a fast charge. Fast charging will occur once
battery pack temperature moderates.
b) Without Red Light (Charge Preparation)-Battery pack is undergoing trickle charge,
because it has been drained excessively during use.
5. The clipper can be left in the charger base for an indefinite period of time. The charger will supply
only what is needed and will not damage the battery due to overcharge.
Diagram A
Diagram B
Diagram C
3
SAFETY RULES FOR CHARGER AND BATTERY PACK
1. Clipper motor switch must be in the "OFF" position for the
charger to operate properly. Do not return the clipper to the
charger base with the motor switch in the "ON" position.
If the clipper is accidentally put on the charger base in the
"ON" position, remove it promptly. Turn clipper off and
return to the charger base.
2. Do not insert anything metallic into the battery pocket of the
charger base (Diagram D).
3. Do not allow the ventilation slots on the charger base to
become blocked or filled with foreign material. Avoid
subjecting the charger to excessively dirty locations. If the
slots become clogged with dust or hair, unplug charger
and gently remove hair with a soft brush or a vacuum
cleaner (Diagram E).
4. Do not attempt to charge any other battery other than the
battery pack designed for your Andis BGR+ Clipper.
5. The battery pack contains an overload protection feature.
Do not attempt to use it to power any other product other
than the Andis Cordless Clipper. Do not touch the exposed
metal contacts on the battery pack with any conductive
material.
6. Do not store battery or charger where it is under 50°F or
over 104°F, as damage may occur (Diagram F).
7. Do not expose the charger base or the battery pack to
excessively damp conditions (Diagram G).
8. Avoid dropping the charger base and the battery pack. Do
not attempt to use a damaged battery pack or charger.
9. Clean external parts of charger with a soft brush or damp
rag. Do not use harsh abrasives, detergents, or solvents
(Diagram H).
Diagram D
Diagram E
Diagram F
Diagram G
Diagram H
4