DSC WT5500 Instructions D'installation page 6

[075] Second Keypad Options
Default Opt. ON
ON 1 Local Clock Display ON
I_____I
OFF I_____I 2 Local Clock Displays 24-hr Time
ON 3 Auto Alarm Scroll ON
I_____I
Language Selection Available From Any
ON 4
I_____I
Menu
OFF I_____I 5 Power LED Enabled
ON 6 Power LED Indicates AC Present ON
I_____I
ON 7 Alarms Displayed While Armed
I_____I
OFF I_____I 8 Auto-Scroll Open Zones ON
[076] Third Keypad Options
Default Opt ON
I____I 1 Armed LED On in Sleep Mode Armed LED Off in Sleep Mode
OFF OFF
ON I____I 2 Keypad Status Shows Stay Arm Keypad Status Shows Stay/Away Arm
I____I 3 Trouble Acknowledgement
OFF ON
Prompt Enabled
ON I____I 4 Ambient Light Sensor ON
ON I____I 5 Late to Open Prompts
ON I____I 6 Power Save Mode ON
OFF I____I 7 For Future Use
I____I 8 Local RF Jam Detect Enabled
OFF ON
NOTE: Programming options indicated in GREY are required for systems compliant with EN50131-1
and EN50131-3 standards. Section [076]: 1=OFF, 3=ON, 8=ON.
[077] LCD Message
I _ __ __I _ _ ___ I _ _ __ _I _ ___ _ I _ __ _ _ I _ _ _ _ _I _ _ _ _ _I _ _ _ __ I _ _ _ _ _ I _ _ _ _ _I _ _ _ _ _I _ _ _ __ I _ _ _ __ I _ _ _ __ I _ _ _ __ I _ _ _ __ |
[077]
I _ __ __I _ _ ___ I _ _ __ _I _ ___ _ I _ __ _ _ I _ _ _ _ _I _ _ _ _ _I _ _ _ __ I _ _ _ _ _ I _ _ _ _ _I _ _ _ _ _I _ _ _ __ I _ _ _ __ I _ _ _ __ I _ _ _ __ I _ _ _ __ |
[078] Download LCD Message Duration
Default: 003 I_____I_____I_____I (Valid entries are 000-255), 000=Unlimited Message Display
OFF
Local Clock Display OFF
Local Clock Displays AM/PM
Auto Alarm Scroll OFF
Language Selection Available in
Installer's Only
Power LED Disabled
Power LED Indicates AC Present OFF
Alarms Not Displayed While Armed
Auto-Scroll Open Zones OFF
OFF
Trouble Acknowledgement Prompt
Disabled
Ambient Light Sensor OFF
Late to Open Prompts
Power Save Mode OFF
For Future Use
Local RF Jam Detect Disabled
This number represents the number of times the downloaded message is cleared by pressing any key
after the message has timed out.
[100] CO Detector Alarm Label
Default: 'CO_Alarm_Evacuate_Area'
Section/Label
I _ ____I _ ____I _ ____I _ ____I _ ____I _ ____I _ ____I _ ____I _ ____I _ ____I _ ____I _ ____I _ ____I _ _____| _ _____| _ ____|
[100]
I _ ____I _ ____I _ ____I _ ____I _ ____I _ ____I _ ____I _ ____I _ ____I _ ____I _ ____I _ ____I _ ____I _ _____| _ _____| _ ____|
[101] System Label
Default: 'System'
Section/Label
I _ ____I _ ____I _ ____I _ ____I _ ____I _ ____I _ ____I _ ____I _ ____I _ ____I _ ____I _ ____I _ ____I _ ____| _ _____| _ ____|
[101]
I _ ____I _ ____I _ ____I _ ____I _ ____I _ ____I _ ____I _ ____I _ ____I _ ____I _ ____I _ ____I _ ____I _ ____| _ _____| _ ____|
[120] Partition 1 Command Output #1
Default: 'Command_O/P_1'
Section/Label
I _ ____I _ ____I _ ____I _ ____I _ ____I _ ____I _ ____I _ ____I _ ____I _ ____I _ ____I _ ____I _ ____I _ ____| _ _____| _ ____|
[120]
I _ ____I _ ____I _ ____I _ ____I _ ____I _ ____I _ ____I _ ____I _ ____I _ ____I _ ____I _ ____I _ ____I _ ____| _ _____| _ ____|
[121] Partition 1 Command Output #2
Default: 'Command_O/P_2'
Section/Label
I _ ____I _ ____I _ ____I _ ____I _ ____I _ ____I _ ____I _ ____I _ ____I _ ____I _ ____I _ ____I _ ____I _ ____| _ _____| _ ____|
[121]
I _ ____I _ ____I _ ____I _ ____I _ ____I _ ____I _ ____I _ ____I _ ____I _ ____I _ ____I _ ____I _ ____I _ ____| _ _____| _ ____|
[996] Reset Programmable Labels to Factory Defaults
[997] View Software Version
[998] Global Label Broadcast
[999] Reset Keypad Programming to Factory Defaults