General Safety Information
DESCRIPTION
This Stainless Steel Submersible Utility Pump is designed
to drain flooded basements, pump domestic waste water,
and pump out gratings and drains. Operates manually.
Has a 115V, 60 Hz., single phase, permanent split capaci-
tor motor. Permanently lubricated ball bearings never need
lubrication. Automatic thermal overload protection. Unit is
equipped with a 15' 18/3 grounding-type power cord.
Discharge is 1-1⁄4".
Housing and base are made of stainless steel. Non-clog
composite impeller, ceramic shaft facing, and oil chamber
for seal lubrication. Motor casing, shaft, and external hard-
ware are stainless steel.
SPECIFICATIONS
Power supply required...................................115V, 60 HZ.
Motor duty ........................................................Continuous
Liquid Temp. Range....................................32° F to 130° F
Dedicated Circuit Requirement (minimum) ..........15 Amps
Pump Discharge .............................................1-1⁄4" MNPT
Discharge Adapters:...............................................1" FNPT
UNPACKING AND INSPECTION
Handle with care. Check items received against packing
list to be sure that all equipment has been received.
Inspect for shipping damage. If found, file claim with carri-
er immediately.
GENERAL SAFETY INFORMATION
READ AND FOLLOW
SAFETY INSTRUCTIONS!
Know the pump application, limitations, and potential
hazards.
Disconnect power before servicing.
Drain all water from system before servicing.
Secure discharge line before starting pump. An unsecured
discharge line will whip, possibly causing personal injury
and/or property damage.
Check hoses for weak or worn condition before each use,
making certain that all connections are secure.
Periodically inspect pump and system components. Keep
free of debris and foreign objects.
NOTE: Not designed for applications involving salt water
1-1⁄4" FNPT x 1-1⁄4" MNPT Elbow
or brine! Use with salt water or brine will void warranty.
Personal Safety:
1. Wear safety glasses at all times when working with
pumps.
2. Keep work area clean, uncluttered, and properly light-
ed – replace all unused tools and equipment.
3. Keep visitors at a safe distance from work area.
4. Make workshop child-proof – with padlocks, master
switches, and by removing starter keys.
When wiring an electrically driven pump, follow all elec-
trical and safety codes that apply.
This equipment is only for use on 115 volt (single phase)
and is equipped with an approved
3-conductor cord and 3-prong, grounding-type plug.
before servicing. This pump has not been investigated for
use in swimming pool areas. Pump is supplied with a
grounding conductor and grounding-type attachment plug.
Be sure it is connected only to a properly grounded
grounding-type receptacle. Where a 2-prong wall recepta-
cle is encountered, it must be replaced with a properly
3/4" Hose
grounded 3-prong receptacle installed in accordance with
codes and ordinances that apply.
All wiring should be performed by a qualified electrician.
Make certain power source conforms to requirements of
your equipment.
Protect electrical cord from sharp objects, hot surfaces, oil,
and chemicals. Avoid kinking cord. Replace or repair
damaged or worn cords immediately.
Do not handle pump or pump motor with wet hands or
when standing on wet or damp surface, or in water.
Do not use this pump in a fish pond.
your basement has water or moisture on floor, do not walk
on wet area until all power has been turned OFF. If shut-
off box is in basement, call electric company or hydro
authority to shut-off service to house, or call your local fire
department for instructions. Remove pump and repair or
replace. Failure to follow this warning can result in fatal
electrical shock. Oil on the pump or in the sump may
indicate motor leakage and electrical shock hazard. Turn
OFF power and check pump for oil leakage from impeller
area. Replace pump if it leaks.
Pump water only with this pump.
To reduce risk of electric shock, pull plug
Risk of electrical shock. Can burn or kill. If
2