Accorroni CHIP MONO DC INVERTER 2500W Mode D'emploi page 31

● CLOCK SETTING
To adjust the real time press CLOCK button, then use ''▲'' and ''▼'' buttons to get the correct time.
♦ Press the button ''▲'' / ''▼'' once to increase/decrease the time setting by 1 minute.
♦ Press the button ''▲'' / ''▼'' for 2 seconds to increase/decrease quickly the time setting. Release the button when reaching
the required time.
♦ Press CLOCK button again the real time is set.
● TIMER MODE SETTING
Push the buttons T-ON-T-OFF to set the timer programming as wished in order to switch on and off the air conditioner at the
desired time.
- How to set TIMER ON
T-ON button can be used to set the timer programming as wished in order to switch on the appliance at your desired time.
1) Press T-ON button, "ON" flashes on the LCD, then you can press the ''▲'' or ''▼'' buttons to select your desired time for
appliance on.
♦ Press the ''▲'' / ''▼'' button once to increase or decrease the time setting by 1 minute.
♦ Hold press the button ''▲'' / ''▼''after for 2 seconds to increase/decrease quickly the time setting. Hold '▲'' or ''▼'' button,
2s later, the time will change quickly until reaching your required time.
♦ Press T-ON to confirm it.
Note: If you don't set the time in 10 seconds after you press T-ON button, the remote controller will exit the T-ON mode
automatically.
2) When your desired time displayed on LCD, press the T-ON button and confirm it, a beep can be heard and then the
TIMER indicator "ON" stops flashing.
- How to cancel TIMER ON
Press the T-ON button again, a "beep" can be heard and the indicator disappears, the T-ON mode has been cancelled.
Note: It is similar to set the TIMER OFF mode; you can make the appliance switch off automatically at your desired time.
● TURBO MODE SETTING:
♦ TURBO mode is used to start or stop fast cooling and heating at high fan speed.
♦ In Turbo mode, you can set airflow direction or timer. If you want to exit from TURBO mode, press any - TURBO, MODE,
FAN or ON/OFF button, the display will return to the original mode.
● LIGHT FUNCTION
Press LIGHT button to turn on the display's light and press this button again to turn off the display's light.
● LOCK FUNCTION
Press the ''▲'' and ''▼'' buttons at the same time to block the last setting operation by the remote controller.
All the buttons disabled, including the ON/OFF button. Press the ''▲'' and ''▼'' buttons again to enable the buttons functions.
● °C / °F FUNCTION
Press the ''MODE'' and ''▼'' buttons at the same time with the unit off to choose the display of temperature in °C and °F.
● WIFI FUNCTION (optional)
Press the "WiFi" button to turn on or turn off the WIFI function. When WIFI function is turned on, the "WIFI" icon will be
displayed on remote controller. Press "MODE" and " WiFi" buttons simultaneously, the remote controller will send WIFI reset
signal and then the WIFI module restore the factory default setting. This function is available only for some models.
1. After putting through the power, press "ON/OFF" button on remote controller to turn on the air conditioner.
2. Press "MODE" button to select your required mode: AUTO, COOL, DRY, FAN, HEAT.
3. Press "▲" or "▼" button to set your required temperature. (Temperature can't be adjusted under auto mode).
4. Press "FAN" button to set your required fan speed: auto, low, medium and high speed.
5. Press "SWING" button to select fan blowing angle.
● ENERGY-SAVING FUNCTION
Press "TEMP" and "CLOCK" simultaneously in COOL mode to start energy-saving function.
Nixie tube on the remote controller displays ''SE''. Repeat the operation to quit the function.
● 8°C HEATING FUNCTION
Press "TEMP" and "CLOCK" simultaneously in HEAT mode to start 8°C Heating Function Nixie tube on the remote controller
30