JB Systems Light LED-UV212 black light Mode D'emploi page 5

ENGLISH
HOW TO SETUP:
MAIN MENU:
 To select any of the menu options, press the MENU button up to when the required option is shown on the
display.
 Select the function with the ENTER button. The display will blink.
 Use DOWN and UP button to choose the desired menu option.
 Once the required menu option is selected, press the ENTER button to select.
Remark: Press the MENU button for about 2 seconds to return to running mode or just wait 8 seconds.
The menu structure is shown below.
DMX512 Address Setting
Used to set the start address in a DMX setup, you can also automatically program the next LED-
UV212 projectors in the same DMX-chain.
Program a DMX start address in 1 unit:
 Press the MENU button until
is shown on the display.
 Press the ENTER button to select.
 Use DOWN and UP buttons to change the DMX512 address.
 Once the correct address shows on the display, press the ENTER button to confirm.
 Press the MENU button for about 2 seconds to return to running mode.
Automatically program the DMX start addresses of several units in a DMX-chain:
 Connect the DMX in/outputs of all projectors together and switch them all on
 On the first unit in the chain:
 Set the DMX-starts address as described above.
 After this, press the MENU button until
 Press the ENTER button to start the automatic programming  all units flash one time to indicate
that the addresses are automatically set, starting from the address programmed in the first unit.
 Press the MENU button on the first unit for about 2 seconds to return to running mode.
Example: the first projector was set to DMX-address 100  when you perform the automatic
addressing, the other projectors in the DMX-chain will receive addresses: 104, 106, 108, 110, ...
(given that the units are in 2ch mode)
JB SYSTEMS
®
OPERATION MANUAL
is shown on the display.
5/45 LED-UV212
ENGLISH
Channel Mode
The unit has 2 different channel modes. Refer to the DMX-chart to see the differences.
 Press the MENU button until
is shown on the display.
 Press the ENTER button to select.
 Use DOWN and UP button to select one of the available channel modes.
 Once the mode is selected, press the ENTER button to confirm.
 Press the MENU button for about 2 seconds to return to running mode.
Sound Mode
Used to choose the desired sound mode to trigger the shows.
 Press the MENU button until
is shown on the display.
 Press the ENTER button to select.
 Use DOWN and UP button to select one of the available modes:

(sound mode ON)  the shows are triggered by the internal microphone.

(sound mode OFF)  the shows are triggered by the speed selected with the shows.
 Once the right mode is selected, press the ENTER button to confirm.
 Press the MENU button for about 2 seconds to return to running mode.
Blackout Mode
Blackout mode: when no DMX-signal is detected, the unit goes in blackout.
No blackout mode: when no DMX-signal is detected, the unit automatically switches to master mode.
ALWAYS set to "No Blackout" when the unit is used in standalone or master (master/slave) mode!!!
 Press the MENU button until
is shown on the display.
 Press the ENTER button.
 Use DOWN and UP button to select Y E S (blackout) or n o (no blackout) mode.
 Once the mode is selected, press the ENTER button to confirm.
 Press the MENU button for about 2 seconds to return to running mode.
Blackout Mode
When the unit is used in standalone mode, you can manually set the strobe and dimmer function.
 Press the MENU button until is shown on the display.
 Press the ENTER button to select.
 Use DOWN and UP button to select one of the 2 available options:
 Select
to select the strobe speed and press ENTER to confirm: use the DOWN and UP
buttons to set the value between 000 (no strobe) and 255 (very fast strobe). Confirm with the
ENTER button.
 Select
to select the dimmer setting and press ENTER to confirm: use the DOWN and UP
buttons to set the value between 000 (no output) and 255 (maximum output). Confirm with the
ENTER button.
 Once both parameters are set, press the MENU button for about 2 seconds to return to running mode.
Led Display
Display on: display is always on.
Display off: display is off when not used.
 Press the MENU button until the display shows
 Press the ENTER button.
 Use DOWN and UP buttons to select
(display always on) or
 Once the mode is selected, press the ENTER button to confirm.
 Press the MENU button for about 2 seconds to return to running mode.
JB SYSTEMS
®
OPERATION MANUAL
.
(display off when not used).
6/45 LED-UV212