urmet domus BiBus II 1072 Manuel D'utilisation page 12

PROGRAMMING
In simple systems, the door unit can be
programmed by means of the LED button
and the two dip-switches without the help of
external devices. In complex systems and for
special programming needs, the device can be
programmed with adapter 1072/60 to be inserted
in the specifi c dedicated minidin connector. The
programming adapter must be connected to
the programming keyboard 1032/65. The system
must be powered for programming.
COMPLETE PROGRAMMING WITH EXTERNAL
DEVICE
Insertion of the programming device is confi rmed by
two beeps and by the led lighting.
Parameters can be programmed or reprogrammed
in any order until the keyboard is extracted. Two
beeps will be heard to confi rm data programming.
A KO signal (two beeps, the second of which at a
lower frequency) will be heard if the programming is
not valid.
Repetitive beeps will be heard in programming if
other modules with the same ID are present.
Press the button to silence the signal.
You are advised to program the data in the following
order for the sake of simplicity:
System type
The digitiser can be confi gured as 1st edition or 2nd
edition. The digitiser must be programmed as
1st edition if there is even only one 1st edition
device in the system (when replacing parts in
old systems). The device must be programmed
as 2nd edition when all the devices in the system
are 2nd edition.
Letter "M" identifi es the type of system:
press M1↵ to program 1st edition
press M2↵ to program 2nd edition
The device will repeatedly beep if there are other
modules with the same ID. Press the button to
silence the signal.
The two dip-switches must not be in the ON position
to program this parameter successfully.
Station type
The digitiser can be confi gured as a main station or
as a secondary station. A secondary digitiser can
be used to send calls to internal stations in the riser
but cannot be used to call the switchboard. In the
case of 1st edition systems, the digitiser will be
automatically confi gured as a main station and
should not be changed.
Letter "I" identifi es the type of station:
press I0↵ to program the main station
press I1↵ to program the secondary station
12
The device will repeatedly beep if there are other
modules with the same ID. Press the button
silence the signal.
The two dip-switches must not be in the ON position
to program this parameter successfully.
Code format
The digitiser can be used to call users with
numeric codes (0001-9999), alphanumeric codes
with alphabetic prefi x (x000-x999) and alphanumeric
codes with alphabetic suffi x (000x-999x). Letters
from A to J can be used.
Letter "F" identifi es the type of programmable code:
numeric code
code with alphabetic prefi x: F2↵
code with alphabetic suffi x:
1st edition system: this programming is not required.
Station number (ID)
A number from 1 to 12 is assigned to each main
calling station. A number from 0 to 9 is assigned to
each secondary station. The secondary number is
in the range from A to J in systems with alphabetic
prefi x.
Letter "N" identifi es the station number:
x station number:
A to J programmed on a secondary station will
automatically be reprogrammed as a prefi x code
format. ID from 0 to 9 on a secondary station will
automatically be reprogrammed as a numeric code
format.
The two dip-switches must not be in the ON position
to program this parameter successfully.
1st edition system: the station number must be in
the range from 1 to 12 (there are not secondary
stations in the system). Assign F as station number
to use the clone function.
Off-hook waiting time
The off-hook waiting time is the maximum time of a
call in which the user can answer the door phone.
All other calling stations will be engaged during this
time. All devices in the system must have the same
off-hook waiting time.
Letter "G" identities the off-hook waiting time:
10s waiting time:
20s waiting time:
30s waiting time:
40s waiting time:
Minimum conversation time (busy)
When a user is called and answers the door phone,
all other call stations will be busy for the minimum
programmed conversation time. A communication
that has just started cannot be interrupted. All
devices in the system must have the same minimum
conversation time (busy time).
to
F1↵
F3↵
Nx↵.
G1↵
G2↵
G3↵
G4↵
DS1072-022A