D - Assembling The Brush; E - Assembling The Pad Holder; F - Assembling The Tank (Optional); G - Assembling The Suction Unit (Optional) - Ghibli & Wirbel SB 133 Utilisation Et Entretien

2.1.d - Assembling the brush (Fig. 6)
- Tilt the machine, pivoting, with the handle
straight, with your feet on the wheels and
place it on the handle.
- Place the brush (16) on the base of the
machine, fitting the appropriate butterfly
coupling (17).
- Make a half turn in the direction of the ar-
row (A) to fit in the brush (16).
- Put the machine back in position.
- When rotation starts, the brush will end
fitting.
To disassemble the brush, tilt machine and
turn the brush (16) in the opposite direction
to that shown by the arrow (A).
WARNING:
Use only brushes supplied by the manu-
facturer for the specific machine model.
Using other types of brushes can com-
promise the safety of the machine.

2.1.e - Assembling the pad holder

(Figs. 6-7)
- Tilt the machine, pivoting, with the handle
straight, with your feet on the wheels and
place it on the handle.
- Place the pad holder (18) on the pad (19)
being careful to centre it properly to avoid
unbalancing the rotation.
- Place the pad holder (18) complete with
pad, on the base of the machine, fitting
the appropriate butterfly coupling, as
described in the "Assembling the brush"
paragraph.
To disassemble the pad holder, tilt the ma-
chine and turn it in the opposite direction to
that shown by the arrow (A).
WARNING:
Use only pads supplied by the manufac-
turer for the specific machine model.
Using other types of pads can compro-
mise the safety of the machine.
2.1.f - Assembling the tank
(optional) (Figs. 8/14)
- Loosen the two screws (20) or the knob
(21) on the upper support (22) of the han-
dle, depending on the machine model
(Fig. 8).
-
Make sure that the lower support (27)
rests on the plate located on the handle
rod (Fig. 11).
- Screw the chain (23) onto the top of the
tank (24) (Fig. 9).
- Connect the tube (25) into the fitting (26)
at the bottom of the tank (24) (Fig. 10).
- Place the tank (24) on the lower support
(27), taking care to align the coupling tab
(28) with its slot (29) (Fig. 11).
- Lower the upper coupling (30) and attach
it to the coupling tab (31) on the top of the
tank (24) (Fig. 12).
- Tighten the two screws (32) or the knob
(33) on the upper support (30) of the han-
dle, depending on the machine model
(Fig. 12).
- Connect the tube (35) fitting (34) to the
hole on the machine body (Fig. 13).
- Attach the chain (36) to the hook (37) on
the handle (Fig. 14).
N.B.:
For some models, you must insert the chain
(36) into the hole at the bottom of the handle
before attaching it to the hook (37) (FIG. 14-
B).
2.1.g - Assembling the suction unit
(optional) (Figs. 15/19)
The suction unit consists of the vacuum
cleaner (38), the suction ring (39) with tube
bundle assembled and the vacuum cleaner
support drum (40) (Fig. 15).
-
Make sure that the lower support (41)
rests on the plate located on the handle
rod (Fig. 16).
- Loosen the two screws and the knob on
the upper support of the handle, depend-
ing on the machine model.
ENGLISH - 4
www.ghibliwirbel.com
Professional Cleaning Machines Since 1968