Technical Data - Parkside WU9079231-8 Instructions De Montage, D'utilisation Et Consignes De Sécurité

List of pictograms used
Read the
instructions!
Observe warnings
and safety
information!
Danger to life and
risk of accidents
for infants and
children!
Workbench
Introduction
We congratulate you on the purchase of your new product. You
have chosen a high quality product. Familiarise yourself with the
product before using it for the first time. In addition, please care-
fully refer to the operating instructions and the safety advice below. Only use
the product as instructed and only for the indicated field of application. Keep
these instructions in a safe place. If you pass the product on to anyone else,
please ensure that you also pass on all the documentation with it.
Intended use
The workbench can be used for clamping workpieces and objects to be
worked on, e.g. for sawing, sanding, polishing, painting, cleaning or holding
together bonding parts. It is intended for do-it-yourself jobs in a domestic set-
ting. Any other use is considered improper, and that also includes disregard-
ing these operating instructions. The workbench is not intended for
commercial purposes.

Technical data

Dimensions (W x H x D): approx. 605 x 790 x 630 mm (unfolded),
605 x 945 x 155 mm (folded)
Empty weight: 6.4 kg
Load-bearing capacity: max. 150 kg when weight is evenly distributed
Scope of delivery and parts description (see Fig. A)
Check that all parts are present, complete and in perfect condition. If any parts
are missing or damaged: do not assemble the workbench and do not use it.
If you notice any damages or missing parts, please contact the retailer from
whom you purchased this product.
4 Plastic feet for the legs
1
2 Clamping jaws
2
1 Leg (left rear)
3
2 Legs (right front and left front)
4
1 Leg (right rear)
5
4 Mounting brackets for the spindle housing
6
2 Spindle housings with crank handle
7
2 Cross braces for the legs
8
1 Clamping plate (rear)
9
1 Clamping plate (front)
10
16 Universal screws 5 x 15
11
8 Slotted-head / Cross-head screws (PH 3) M 6 x 32 each with 1 washer
12
and 1 nut (self-locking)
6 Hexagon screws M 8 x 40 each with 2 washers and 1 nut (self-locking)
13
1 Open-ended spanner NW 10/13 mm
14
Maximum load
max.
150 kg
150 kg
TÜV Süd-certified
safety
Safety notes
Check the product after it has been delivered and before first use to ascertain
the condition and functionality of all parts. Never use the product if it is damaged.
Otherwise, there is the risk of injury. Never use a damaged product.
Observe the following safety notes in order to avoid injuries and damage to
property:
ACCIDENTS FOR INFANTS AND CHILDREN! Never
leave children unsupervised with the packaging material.
There is a danger of suffocation. Keep this product out of the reach of
children. This product is not a toy.
Always keep children away from the product. Children frequently under-
estimate the dangers. Store the product in a dry, enclosed room, inacces-
sible to children.
Check that all screw connections are correctly positioned before each use.
Check that all moving parts are moving smoothly.
Do not use the workbench as seating or as a step, standing aid, or ladder.
Do not use the workbench to erect scaffolding.
Do not exceed the maximum permissible load of 150 kg when weight is
distributed evenly.
Where possible, position the laid out and clamped objects in the centre
of the worktop.
Long workpieces require additional support at the protruding ends.
Only set up the workbench on a firm, level surface, so that all four legs are
in contact with the ground. Level out any slight irregularities with balancing
blocks.
When working, fix the workpieces securely using the clamping device.
Only exert pressure on the worktop or the workpiece in a vertical direction.
When under diagonal or lateral pressure, the workbench will tip over.
Do not step on the struts to stabilise the workbench.
Keep the workbench out of reach of children. Only allow children to
work on the workbench when supervised.
Store the workbench in a dry location.
Do not expose the workbench to rain.
Be aware of the remaining risks
Even when the product is used properly, there are still some remaining
risks that are unavoidable. These are:
· Body parts being pinched by moving parts.
· The workpiece being damaged due to being clamped too tightly.
Assembly
Note: The workbench is assembled upside down, and only then stood up
on its legs.
On both spindle housings
7
Twist off the nut so that you can then install the mounting bracket
a 13 mm socket to do this. Tighten the nut just enough so that the mounting
bracket can still move slightly (see Fig. B).
6
On both spindle housings
7
Unscrew both screws so that you can then install the other mounting
bracket (see Fig. C). Tighten the screws.
6
Lay down both clamping plates
The sides with the indentations must be opposite each other (see Fig. D).
Use the screws to mount both spindle housings
11
left of the clamping plates
9
Assemble the legs , ,
3 4 5
The elbowed ends of the legs
the screws and nuts just enough so that the legs
13
pivot (see Fig. G to J).
Fold out the legs , , and move the struts into position (see Fig. K).
3 4 5
DANGER TO LIFE AND RISK OF
:
:
, with the base facing upwards.
9 10
on the right and
7
, (see Fig. E and F).
10
using the washers, nuts and screws
, , must face outwards. Tighten
3 4 5
, ,
3 4 5
. Use
6
.
13
can still
GB/IE 7