Makita DLS211 Manuel D'instructions page 33

Special Max Width Cutting
Capacities Technique
The maximum cutting capacity of width can be achieved
by following the steps below:
For the maximum cutting width of this tool, refer
to the cutting capacities for special cuttings in the
SPECIFICATIONS section.
1. Set the tool at 0° or 45° miter angle and make sure
that the turn base is locked. (Refer to the section for
PLWHU DQJOH DGMXVWPHQW
2. Remove both right and left upper fences temporar-
ily and set aside them.
3. Cut a platform to the dimensions indicated in the
¿JXUH XVLQJ D  PP WKLFN ÀDW VWRFN PDWHULDO VXFK DV
wood, plywood or particle board.
Fig.60: 1. 0° Miter angle: Over 450 mm 2. 45° Miter
angle: Over 325 mm 3. 38 mm 4. Over
760 mm
WARNING:
%H VXUH WR XVH ÀDW VWRFN DV D
platform. 6WRFN WKDW LV QRW ÀDW PD\ PRYH GXULQJ WKH
cutting operation which may result in kickback and
VHULRXV SHUVRQDO LQMXU\
NOTE: The maximum cutting capacity in height will
be reduced by the same amount as the platform
thickness.
4. Place the platform on the tool so that it extends
equally over each side of the tool base.
Secure the platform to the tool using four 6 mm wood
screws through four holes in the lower fences.
Fig.61: 1. 6FUHZV WZR HDFK VLGH 2. Lower fence
3. Base 4. Platform
WARNING:
Make sure that the platform is lay-
LQJ ÀDW DJDLQVW WKH WRRO EDVH DQG VHFXUHG ¿UPO\
to the lower fences using the four screw holes
provided. Failure to properly secure the platform may
result in movement and possible kickback resulting in
VHULRXV SHUVRQDO LQMXU\
WARNING:
(QVXUH WKDW WKH WRRO LV ¿UPO\
PRXQWHG WR D VWDEOH DQG ÀDW VXUIDFH Failure to
properly mount and secure the tool could cause the
tool to be unstable resulting in a loss of control and/
or the tool falling which may result in serious personal
LQMXU\
5. Install the upper fences on the tool.
WARNING:
Do not use the tool without upper
fences installed. The upper fences provide the ade-
quate support required to cut the workpiece.
If the workpiece is not supported properly, it may
move resulting in possible loss of control, kickback
DQG VHULRXV SHUVRQDO LQMXU\
6. Place the workpiece to be cut on the platform
secured to the tool.
7. 6HFXUH WKH ZRUNSLHFH ¿UPO\ DJDLQVW WKH XSSHU
fences with a vise before cutting.
Fig.62: 1. Upper fence 2. Vertical vise 3. Workpiece
4. Platform
8. Make a cut through the workpiece slowly accord-
ing to the operation explained in the section for slide
SXVK FXWWLQJ
WARNING:
Ensure that the workpiece is
secured with the vise and make the cut slowly.
Failure to do so may cause the workpiece to move
resulting in possible kickback and serious personal
LQMXU\
WARNING:
Be aware that the platform may
become weakened after several cuts are per-
formed at various miter angles. If the platform
becomes weakened due to the multiple kerf cuts left
in the material, the platform should be replaced. If the
weakened platform is not replaced, it may cause the
workpiece to move, during cutting, resulting in possi-
EOH NLFNEDFN DQG VHULRXV SHUVRQDO LQMXU\
Groove cutting
WARNING:
Do not attempt to perform this
type of cut by using a wider type blade or dado
blade. Attempting to make a groove cut with a wider
blade or dado blade could lead to unexpected cutting
results and kickback which may result in serious
SHUVRQDO LQMXU\
WARNING:
Be sure to return the stopper arm
to the original position when performing other
than groove cutting. Attempting to make cuts with
the stopper arm in the incorrect position could lead to
unexpected cutting results and kickback which may
UHVXOW LQ VHULRXV SHUVRQDO LQMXU\
For a dado type cut, perform as follows:
1. $GMXVW WKH ORZHU OLPLW SRVLWLRQ RI WKH VDZ EODGH
XVLQJ WKH DGMXVWLQJ VFUHZ DQG WKH VWRSSHU DUP WR OLPLW
the cutting depth of the saw blade. Refer to the section
for stopper arm.
2. $IWHU DGMXVWLQJ WKH ORZHU OLPLW SRVLWLRQ RI WKH VDZ
blade, cut parallel grooves across the width of the work-
SLHFH XVLQJ D VOLGH SXVK FXW
Fig.63: 1. Cut grooves with blade
3. Remove the workpiece material between the
grooves with a chisel.
Wood facing
WARNING:
Use screws to attach the wood
facing to the guide fence. The screws should be
installed so that the screw heads are below the
surface of the wood facing so that they will not
interfere with the positioning of the material being
cut. Misalignment of the material being cut can case
unexpected movement during the cutting operation
which may result in a loss of control and serious
SHUVRQDO LQMXU\
33 ENGLISH