Publicité
Les langues disponibles
Les langues disponibles
Note: Check the correct assembly of the liner front area by lifting and lowering the VPS. These movements should be smooth. If this
is not the case, repeat the steps 1.5 and 2.2.
2.4 Insert the chin strap into the appropriate space on the cheek pad; insert the back hard plastic flap of the cheek pad under the
shell sealing edge, between the cheek pad and the inner shell.
2.5 Make sure that the cheek pad is in the correct position so that all the snap buttons are in line with their housings.
2.6 Insert the hard flap all the way into the groove under the base edge and hook the three buttons (Fig.10 A).
2.7 Insert the front cheek pad flap between the chin guard and the base edge trim (Fig.10 B).
Warning: The buttons are not hooked until a click is heard.
2.8 Check that the strap comes out properly from the cheek pad.
2.9 Repeat steps 2.4 to 2.7 on the other side of the cheek pad.
WARNING!!!
-
Remove the padding only when cleaning or washing is required.
-
Never use the helmet if the inner comfort padding and the cheek pads have not been correctly and completely restored.
-
Delicately hand-wash in lukewarm water (max. 30°C) and neutral soap.
-
Rinse off with cold water and dry up at room temperature away from direct sunrays.
-
Never machine-wash the inner comfort padding.
-
The inner polystyrene is an easily deformable material, in fact it is apt to change or get partially destroyed to help absorb shocks.
-
Use a wet cloth to clean it and let it dry at room temperature away from direct sunrays.
-
Do not modify the helmet's internal polystyrene components in any way.
-
Never use tools or equipment of any sort to carry out the steps described above.
•
EYEWEAR ADAPTIVE
The new and exclusive Eyewear Adaptive (EA) is designed for the comfort of eyeglass wearers. In a quick and easy way, EA allows us
to obtain a space in the cheek pads for the glasses temples.
The system is reversible, so the cheek pads can be returned to the initial configuration.
To enjoy the comfort of the helmet with glasses:
1. Remove the cheek pads from the helmet (please refer to paragraph "removable inner comfort padding", section "removal", 1.1,
1.2 and 1.3).
Note: Check the correct assembly of the liner front area by lifting and lowering the VPS. These movements should be smooth. If this
is not the case, repeat the steps 1.5 and 2.2.
2.4 Insert the chin strap into the appropriate space on the cheek pad; insert the back hard plastic flap of the cheek pad under the
shell sealing edge, between the cheek pad and the inner shell.
2.5 Make sure that the cheek pad is in the correct position so that all the snap buttons are in line with their housings.
2.6 Insert the hard flap all the way into the groove under the base edge and hook the three buttons (Fig.10 A).
2.7 Insert the front cheek pad flap between the chin guard and the base edge trim (Fig.10 B).
Warning: The buttons are not hooked until a click is heard.
2.8 Check that the strap comes out properly from the cheek pad.
2.9 Repeat steps 2.4 to 2.7 on the other side of the cheek pad.
WARNING!!!
-
Remove the padding only when cleaning or washing is required.
-
Never use the helmet if the inner comfort padding and the cheek pads have not been correctly and completely restored.
-
Delicately hand-wash in lukewarm water (max. 30°C) and neutral soap.
-
Rinse off with cold water and dry up at room temperature away from direct sunrays.
-
Never machine-wash the inner comfort padding.
-
The inner polystyrene is an easily deformable material, in fact it is apt to change or get partially destroyed to help absorb shocks.
-
Use a wet cloth to clean it and let it dry at room temperature away from direct sunrays.
-
Do not modify the helmet's internal polystyrene components in any way.
-
Never use tools or equipment of any sort to carry out the steps described above.
•
EYEWEAR ADAPTIVE
The new and exclusive Eyewear Adaptive (EA) is designed for the comfort of eyeglass wearers. In a quick and easy way, EA allows us
to obtain a space in the cheek pads for the glasses temples.
The system is reversible, so the cheek pads can be returned to the initial configuration.
To enjoy the comfort of the helmet with glasses:
1. Remove the cheek pads from the helmet (please refer to paragraph "removable inner comfort padding", section "removal", 1.1,
1.2 and 1.3).
10
10
Publicité
