Sprintus CRAFTIX M Mode D'emploi Original page 15

inated items that cannot be satisfactorily cleaned must be
disposed of. Such items must be disposed of in impermeable
bags in accordance with the applicable regulations for the dis-
posal of such waste.
7.1 Changing fleece filter bag
See Fig. 4 - 6
1. Close the vacuum connection with a sealing plug
2. Unlock the locking tabs and remove the motor head.
3. Remove the fleece filter bag from the flange and close it
tightly with the cap.
4. Dispose of used fleece filter bags in accordance with legal
requirements.
5. Put on the new fleece filter bag and snap in the seal.
6. Put on the motor head and lock it with the locking tabs.
7.2 Changing disposal bag
See Fig. 8-11, 4-5
1. Close the vacuum connection with a sealing plug
2. Switch the vacuum cleaner on again and wait for the clean-
ing cycle to clean the residual dust from the filter cartridge.
Then unplug the vacuum cleaner. To ensure that the dust
settles in the container, wait approx. 30 seconds.
3. Remove the disposal bag from the flange and close it tightly
with the cap
4. Carefully close the disposal bag tightly with the enclosed
cable tie.
5. Dispose of used disposal bag in accordance with legal re-
quirements.
6. Put on a new disposal bag and put it over the edge of the
container. Note that the holes provided above the flange
must be placed over the electrodes of the water cut-off.
7. Put on the motor head and lock it with the locking tabs
7.3 Cleaning the electrodes
See Fig. 39
Clean the electrodes with a brush or cloth
7.4 Cleaning the cooling air filter
See Fig. 38
To ensure that the motor is cooled sufficiently, make sure that
the cooling air filter is clean. Otherwise, overheating and sub-
sequent thermal protection shutdown may occur.
Vacuum the cooling air filter with a vacuum cleaner.
7.5 Changing filter cartridge
See Fig. 29-35
The tool for changing the filter is attached to the rear of the
chassis.
1. Loosen the 6 screws on the underside of the motor head
along the fastening ring. (Do not unscrew completely)
2. Loosen the fastening ring by turning it and remove it.
3. Remove the filter cartridge and immediately seal it in a
dust-tight plastic bag and dispose of it as intended.
4. New filter cartridge Item no.: Insert 118100.
5. Attach the fastening ring and lock it by turning.
6. Tighten all 6 screws.
7.6 Cleaning the exhaust air filter
See Fig. 36-37
1. Remove the filter cassette on the back of the motor head
and take out the exhaust air filters.
2. Clean (vacuum, wash out) or change the exhaust air filter.
Item no. 118103 or 118102
3. Insert new or cleaned exhaust air filters and reinsert the
filter cassette into the motor head.
7.7 Cleaning filter cartridge
1. Remove the vacuum hose.
2. Close the vacuum connection with a sealing plug.
3. Switch on the vacuum cleaner and wait for the cleaning cy-
cle to clean the residual dust from the filter cartridge.
If the filter is still not clean, switch the vacuum cleaner on again
and wait for another cleaning cycle.
8. TRANSPORT
Remove the vacuum hose and close the vacuum socket with
the cap.
Stow the accessories in the accessory storage provided at the
back of the vacuum cleaner. Wrap the vacuum hose around
the vacuum cleaner using the hose hooks. Pin the hose ends
together to prevent dirt particles from escaping.
Wind the cable from the vacuum cleaner and place it around
the push bar or the hose hook.
When transporting in vehicles, ensure that the vacuum cleaner
is secured against slipping and tipping in accordance with the
applicable directives.
9. REPAIR
m Vacuum cleaners that have not been repaired properly
pose a danger to the user!
Repairs may only be carried out by qualified personnel,
e.g. customer service. Only use original spare parts.
I 15