Tennant V-WD-27 Manuel De L'opérateur page 3

Warning: Do not tamper or modify the
appliance. Failure to comply with these
instructions
personal injury or death. Tampering will void the
warranty.
The manufacturer refuses all responsibility
for damages or injuries due to improper
use of the machine or in case of failure to
failure to comply with the instructions given in
this manual.
Always disconnect power cord from
power source after operating and before
servicing. After every use and before
sending the appliance to a service center, it must
be thoroughly cleaned and tank rinsed out to
avoid hazard.
-
Do routine maintenance. Inspect gaskets seals,
plastic parts, filters, switches and replace those
which have begun to leak or are damaged.
-
Using a machine with a damaged power cord could
result in an electrocution. Check the cord looking
for cuts, cracks or aging signs and replace it, if it's
necessary.
-
Do not use an extension cord with this machine.
-
Only an authorized service center can do reparation
or maintenance of the appliance. Use only original
spare parts.
-
To keep the appliance fully functional it is necessary
to clean main polyester filter by shaking it after every
use and replacing filter bag if it's full.
-
Clean every part of the appliance after each use:
empty the tank, shake the filters, replace filtering
bag if it's full and clean the machine with a damp
cloth before storing the vacuum cleaner.
-
WARNING: In case of foam or liquid leak turn off the
appliance immediately.
-
WARNING: In case overturning, lift the appliance in
the upright position before switching the motors off.
-
Don't pick up water from sink or tub. Do not use
appliance as a pump to clean out clogged drains,
sinks, or other plumbing fixtures. The appliance is
intended for vacuuming air and water mixtures.
-
Do not use or pick up aggressive soaps, they could
damage the appliance.
WARNING: The float valve will stop the
vacuuming when the tank is full of liquids
or if machine overturns; ensure float valve
is installed and operating properly before use.
-
WARNING: Do not use outdoors or in a cold
environment.
-
During a power quality disturbance of the facilities
electrical grid, this appliance may cause temporary
drops in voltage.
DRY PICK UP (PAGE 52)
1. Insert main polyester filter into the tank (Fig. 1).
2. Mount the motor head on top of tank and lock it
with latches (Fig. 3).
3. Push vacuum hose into hose inlet (Fig. 4).
4. Attach wand and desired tool to hose ends (Fig.
5).
5. If your vacuum is equipped with vacuum bag,
slide vacuum bag over the deflector (Fig. 7).
6. Plug power cord into a properly grounded outlet
and turn appliance on (Fig. 6).
could result in severe
WET PICK UP (PAGE 52)
1. Remove main polyester filter from the tank (Fig.
2).
2. Mount the motor head on top of tank and lock it
with latches (Fig. 3).
3. Push vacuum hose into hose inlet (Fig. 4).
4. Attach wand and hoses to hose end (Fig. 5).
5. Attach squegee floor tool to the other end.
6. Plug power cord into a properly grounded outlet
and turn appliance on (Fig. 6).
COMPONENTS DESCRIPTION (PAGE 52)
A - Motor head
B - On/Off Switch
C - Latches
D - Inlet
E - Tank
F - Castor wheels
G - Main polyester filter. Use only for dry pick up
(not for wet pick up).
H - Float valve
I - Vacuum hose
J - Power cord
K - Wand Clip (only V-WD-62)
L - Two-piece wand
M - Hose nozzle
N - Crevice tool
O - Round brush
P - Tool adaptor (only V-WD-62 and 72)
Q - Squeegee floor tool
R - Brush floor tool
S - Upholstery tool (only V-WD-27)
T - Trolley (only V-WD-62 and 72)
TENNANT V-WD-27 / V-WD-62 / V-WD-72
EN
3