Intimus 120SP2 Instructions D'opération page 3

USA
CONTROLS:
8 = Control display (Fig. 1)
"Door open"/ "Door malfunction"
a) "Door open"
Comes on if the door on the lower part
of the machine is opened. The machine
switches off automatically and cannot
be started as long as the door remains
open.
b) "Electrical fault"
Flashes when there is an electrical fault
in the door sensor. The machine switches
off. Please contact your dealer.
9 = Control display (Fig. 1)
To find out what to do see the relevant
description under the "MALFUNCTION"
section.
"Electrical fault"
Flashes when there is an electrical fault
inside the control board. At the same
time the function button (2) LED display
flashes. The machine switches off.
Please contact your dealer.
10 = Control display
"CD/DVD container full" (Fig. 1)
Comes on when the CD/DVD container is
full and must be emptied. The cutting unit
for reducing CD/DVD switches off. The
emptying procedure must be acknowledged
on the forward button (3).
Note: The cutting unit for reducing paper
can be used furthermore.
11 = Control display
"Paper collection container / bag full"
(Fig. 1)
Comes on when the paper collection
container / paper collection bag is full
and must be emptied. The cutting unit for
reducing paper switches off.
Note: The cutting unit for reducing CD/
DVD can be used furthermore.
12 = Paper feed slot (Fig. 3)
13 = CD/DVD feed slot (Fig. 3)
14 = Paper collection container (Fig. 4)
15 = Paper collection bag (Fig. 4)
16 = CD/DVD collection container (Fig. 4)
17 = Oil reservoir (Fig. 4)
The shredder may not be used as a
step ladder or as a seat. Danger of
falling due to breakage!
SWITCHING THE MACHINE ON:
Proceed as follows to switch the machine to
"Ready":
- Press the function button (2) briefly.
- The function button (2) LED display
on for "Ready".
- The machine can be loaded.
MATERIAL FEED:
Feed paper into the cutting mechanism through
the paper feed slot (12) (Fig. 3).
Feed data carriers (CD, DVD or credit card)
into the cutting mechanism individually into the
separate CD/DVD feed slot (13) (Fig. 3).
The machine automatically switches to forwards
running, draws the material in and automatically
switches off after shredding.
OPERATION
When shredding papers, do not
shred CD/DVD at the same time,
and vice versa!
Note: For shredding transparent films, the
machine must be manually switched to forwards
running (press and hold the forwards button (3)
for approx. 2 secs.).
By briefly pressing the function button (2) (Stop
function), the shredding process can be stopped
at any time. To continue, press and hold the
forwards button (3) for approx. 2 secs.
If the machine is not used for a period of approx.
5 mins., it automatically switches off.
Never feed the shredder with a
quantity of material exceeding the
maximum indicated. Refer to the
TECHNICAL DATA section!
Should
overloaded, follow the instructions
under "MATERIAL JAM IN MACHINE"
under "MALFUNCTIONS".
Two separate collection containers ensure
that waste is separated properly.
EMPTYING THE
CONTAINER / PAPER COLLECTION BAG (Fig. 4):
If the paper collection container / bag is full the
machine switches off. The control display
comes on. Proceed as follows:
- Open the door. The control display
comes on. If there is still material in one of
the feed slots, the control display
comes on.
Paper collection container (14):
- Pull out the receptacle from the lower part
of the housing and empty the contents. The
control display
- Slide the emptied receptacle (14) back into the
lower part of the housing and close the door.
The control display
- If the control display
the forward button (3) briefly. The remaining
material in the feed slot is shredded and the
display go out.
Paper collection bag (15):
- Take the collection bag and the frame out of
the bottom part of the housing. Remove the
bag and dispose of the contents. The control
display (11) goes out.
comes
120 SP2(SC2)/CP4(CC3)/CP5(CC4)/CP6(CC5)/CP7(CC6)
the machine become
PAPER COLLECTION
(11)
(8)
(6) also
(11) goes out.
(8) goes out.
(6) comes on, press
16
17
Fig. 4
3
- Fit the emptied bag onto the bag frame and
insert the bag and the frame into the bottom
part of the housing again. Close the door. The
control display (8) goes out.
- If the control display (6) comes on, press
the forward button (3) briefly. The remaining
material in the feed slot is shredded and the
display go out.
Note: The machine will only run if the door is
closed.
EMPTYING THE CD/DVD
CONTAINER (Fig. 4):
Note: The "CD container full" is monitored by
counting the number of shredding processes
performed.
If the number of CD's/DVD's pre-programmed
into the control unit (about 20) is shredded the
machine switches off. The control display
(10) comes on.
Proceed as follows:
- Open the door. The control display
comes on and the forward button (3) LED
display as well as the control display
flashes.
- Remove the collection container (14) from
the inside of the door and dispose of the
contents.
- Press the forward button (3) briefly to
acknowledge that the CD/DVD container has
been emptied. The counting process begins at
zero again. The control display
forward button (3) LED display
- Attach the emptied container to the door again
and close the door.
Note: The machine will only run if the door is
closed.
DYNAMIC LOAD DISPLAY:
To prevent a material jam and thus ensure
a continual, effective destruction of the data
carriers, the current load level of the motor is
displayed during the shredding process by a
coloured, diffuse light in the feed slot as follows:
Green light: load < 50%
Yellow light: load 50 - 75%
Red light: load 75 - 100%
14 15
COLLECTION
(8)
(10)
(10) and the
go out.