baltur BTG 20 LX Notice D'instructions page 33

WARNING NOTES FOR THE USER HOW TO
I
USE THE BURNER SAFETY
FOREWORD
These warning notes are aimed at ensuring the safe use of the
components of heating systems for civil use and the production
of hot water. They indicate how to act to avoid the essential safety
of the components being compromised by incorrect or erroneous
installation and by improper or unreasonable use. The warning
notes provided in this guide also seek to make the consumer more
aware of safety problems in general, using necessarily technical
but easily understood language. The manufacturer is not liable
contractually or extra contractually for any damage caused by
errors in installation and in use, or where there has been any
failure to follow the manufacturer's instructions.
GENERAL WARNING NOTES
• The instruction booklet is an integral and essential part of the
product and must be given to the user. Carefully read the warnings
in the booklet as they contain important information regarding safe
installation, use and maintenance. Keep the booklet to hand for
consultation when needed.
• Equipment must be installed in accordance with current
regulations, with the manufacturer's instructions and by qualified
technicians. By the term 'qualified technicians' is meant persons
that are competent in the field of heating components for civil use
and for the production of hot water and, in particular, assistance
centres authorised by the manufacturer. Incorrect installation
may cause damage or injury to persons, animals or things. The
manufacturer will not in such cases be liable.
• After removing all the packaging make sure the contents are
complete and intact. If in doubt do not use the equipment and
return it to the supplier. The packaging materials (wooden crates,
nails, staples, plastic bags, expanded polystyrene, etc.) must
not be left within reach of children as they may be dangerous to
them. They should also be collected and disposed on in suitably
prepared places so that they do no pollute the environment.
• Before carrying out any cleaning or maintenance, switch off the
equipment at the mains supply, using the system's switch or
shut-off systems.
• If there is any fault or if the equipment is not working properly,
de-activate the equipment and do not attempt to repair it or
tamper with it directly. In such case get in touch with only
qualified technicians. Any product repairs must only be carried
out by BALTUR authorised assistance centres using only original
spare parts. Failure to act as above may jeopardise the safety
of the equipment. To ensure the efficiency and correct working
of the equipment, it is essential to have periodic maintenance
carried out by qualified technicians following the manufacturer's
instructions.
• If the equipment is sold or transferred to another owner or if the
owner moves and leaves the equipment, make sure that the
booklet always goes with the equipment so it can be consulted
by the new owner and/or installer.
• For all equipment with optionals or kits (including electrical), only
original accessories must be used.
BURNERS
• This equipment must be used only for its expressly stated use:
applied to boilers, hot air boilers, ovens or other similar equipment
and not exposed to atmospheric agents. Any other use must be
regarded as improper use and hence dangerous.
• The burner must be installed in a suitable room that has ventilation
in accordance with current regulations and in any case sufficient
to ensure correct combustion
• Do not obstruct or reduce the size of the burner' air intake grills or
the ventilation openings for the room where a burner or a boiler
is installed or dangerous mixtures of toxic and explosive gases
may form.
• Before connecting the burner check that the details on the plate
correspond to those of the utility supplies (electricity, gas, light
oil or other fuel).
• Do not touch hot parts of the burner. These, normally in the areas
near to the flame and any fuel pre-heating system, become hot
when the equipment is working and stay hot for some time after
the burner has stopped.
• If it is decided not to use the burner any more, the following actions
must be performed by qualified technicians:
a) Switch off the electrical supply by disconnecting the power
cable from the master switch.
b) Cut off the fuel supply using the shut-off valve and remove the
control wheels from their position.
c) Render harmless any potentially dangerous parts.
Special warning notes
• Check that the person who carried out the installation of the
burner fixed it securely to the heat generator so that the flame
is generated inside the combustion chamber of the generator
itself.
• Before starting up the burner, and at least once a year, have
qualified technicians perform the following operations:
a) Set the burner fuel capacity to the power required by the heat
generator.
b) Adjust the combustion air flow to obtain combustion yield of at
least the minimum set by current regulations.
c) Carry out a check on combustion to ensure the production
of noxious or polluting unburnt gases does not exceed limits
permitted by current regulations.
d) Check the adjustment and safety devices are working properly.
e) Check the efficiency of the combustion products exhaust duct.
f) Check at the end of the adjustments that all the adjustment devices
mechanical securing systems are properly tightened.
g) Make sure that the use and maintenance manual for the burner
is in the boiler room.
• If the burner repeatedly stops in lock-out, do not keep trying to
manually reset but call a qualified technicians to sort out the
problem.
• The running and maintenance of the equipment must only be
carried out by qualified technicians, in compliance with current
regulations.
3 / 28
0006080937_2010/03
E
N
G
L
I
S
H