Adjust Flame Height - Whirlpool WEG750H0H Manuel Du Propriétaire

Masquer les pouces Voir aussi pour WEG750H0H:
Table des Matières

Publicité

Les langues disponibles

Les langues disponibles

To Convert Oven Broil Burner (Propane Gas to
Natural Gas)(On some models)
1. Remove 1 screw from the broil burner.
2. Remove the flame spreader.
3. Remove the broil burner from the broil burner orifice hood.
NOTE: The broil burner will hang in the back of the oven while
changing the orifice hood.
A. Broil burner
B. Flame spreader
C. Screws
D. Orifice hood
4. Apply masking tape to the end of a 3/8" (1 cm) nut driver to
help hold the gas orifice spud in the nut driver while changing
it. Press nut driver down onto the gas orifice spud and remove
by turning the Propane gas broil burner orifice hood
counterclockwise to remove. The hood will be stamped with a
"100."
5. Replace the "100" hood with a "155" hood. Install the Natural
gas broiler burner orifice hood, turning it clockwise until snug.
IMPORTANT: Do not overtighten.
A. Orifice hood
6. Place the broil burner on the broil burner orifice hood. Insert
the broil burner ceramic igniter in the hole in the rear of the
oven.
7. Replace the flame spreader with all 4 tabs facing up and the
notches toward the rear of the oven.
8. Position the broil burner against the top of the oven and attach
it with 1 screw.
9. Replace the storage drawer. See the "Remove/Replace
Drawer" section.
10. Replace the oven door. See the "Oven Door" section.
11. Replace the oven racks.
24
Complete Installation (Propane Gas to Natural
Gas)
1. Refer to the "Make Gas Connection" section for proper
connection of the range to the gas supply.
2. Refer to the "Electronic Ignition System" section for proper
burner ignition and operation.
3. Refer to the "Adjust Flame Height" section for burner flame
adjustments.
IMPORTANT: You may have to adjust the low setting for each
cooktop burner.
Checking for proper cooktop, bake and broil burner flame is
very important. Natural gas flames do not have yellow tips.
4. Refer to "Complete Installation" in the "Installation
Instructions" section of these instructions to complete this
procedure.
IMPORTANT: Make sure to save the orifices that have just been
replaced in the conversion.

Adjust Flame Height

Adjust Surface Burner Flame
Adjust the height of top burner flames. The cooktop "low" burner
flame should be a steady blue flame approximately 1/4" (6.3 mm)
high. Propane gas flames have a slightly yellow tip.
A. Low flame
B. High flame
To Adjust Standard Burner:
The flame can be adjusted using the adjustment screw in the
center of the valve stem. The valve stem is located directly
underneath the control knob.
If the "Low" Flame Needs to Be Adjusted:
1. Light 1 burner and turn to lowest setting.
2. Remove the control knob.
Hold the knob stem with a pair of pliers. Use a small flatblade
screwdriver to turn the screw located in the center of the
control knob stem until the flame is the proper size. Turning
the screw clockwise will increase the flame size and
counterclockwise will decrease the flame size.
A. Control knob stem
B. Screwdriver
C. Pliers
3. Replace the control knob.
4. Test the flame by turning the control from the low position to
the high position, checking the flame at each setting.
5. Repeat the previous steps for each burner.

Publicité

Table des Matières
loading

Ce manuel est également adapté pour:

Wega25h0h

Table des Matières