Virutex FR98H Mode D'emploi page 6

E N G L I S H
FR98H SHAPER MACHINE
(Illustrations in page 32)
1. TECHNICAL DATA
Universal motor.........................................50/60 Hz
Power.........................................................1,300 W
Cutter-holder speed..............................23.000/min
Maximum pitch diameter of the cutters.............49 mm
Maximum width/depth..............................40/20 mm
Maximum depth per pass (1st/2nd/3rd)...12+5+3 mm
Weight without standard accessories..............4.9 kg
Weighted equivalent continuous
acoustic pressure level A............................................99 dBA
Acoustic power level A...........................................110 dBA
Uncertainty............................................................K = 3 dBA
Wear ear protection!
Vibration total values......................................a
Uncertainty...........................................................K: 1.5 m/s
2. SAFETY INSTRUCTIONS FOR MACHINE OPERATION
Before using the machine carefully read
the GENERAL SAFETY INSTRUCTIONS LE-
AFLET, which is included in the machine
documentation.
1. Before connecting the machine to the mains, check
that the power supply voltage coincides with that shown
on the specification plate.
2. Wear safety goggles when working with this machine.
3. Keep hands clear of the cutting area and always hold
the machine by the grips, with both hands.
4. Avoid cutting through nails; inspect the working
surface before beginning to shape it.
5. Always start the machine with the main switch.
6. Never let go of the machine until all moving parts
have come to a complete rest.
7. Disconnect the machine from the mains electricity
supply before carrying out any maintenance operation.
8. Never use incorrect or defective cutters or cutters
in poor condition. Use only VIRUTEX original cutters
and spare parts.
3. STANDARD EQUIPMENT
You will find the following items inside the box:
• FR98H shaper machine equipped with cutter-holder
and M.D. straight, reversible cutters.
• Set of 2 moulding cutters.
6
• Allen key b.c.: 2.5 mm
• Allen key b.c.: 5 mm
• Connect for external aspiration
• Instruction manual and other documentation
4. OPTIONAL ACCESSORIES AND TOOLS
• 6446073 3.5 m Standard dust collector attachment
• 9800150 Radius copier
• 9800050 Base with FR98H guide extension
• 9841004 Set of 2 M.D. straight reversible cutters
• 9845239 Set of cutter-holders for straight cutters
• 9841005 Set of 2 M.D. 1/4 R=5, 10 and 15
• 9845270 Set of cutter-holders for 1/4 R:5/10/15 cutters
• 9841006 Set of 2 M.D. moulding cutters
• 9845273 Set of cutter-holders for moulding cutters
• 9841010 Set of 2 M.D. 1/4 R=25
• 9845271 Set of cutter-holders for 1/4 R:25 cutters
• 9841011 Set of 2 M.D. 1/2 R=4/5/7
• 9845272 Set of cutter-holders for 1/2 R:4/5/7 cutters
• 9841012 Set of 2 M.D. R=-25
• 9845332 Set of cutter-holders for R:-25 cutters
• 9841013 Set of 2 M.D. 1/4 R=20
: 3.2 m/s
2
• 9845333 Set of cutter-holders for 1/4 R:20 cutters
h
2
• 9841014 Set of 2 M.D. 2R=10
• 9845334 Set of cutter-holders for 2R:10 cutters
• 9841015 Set of 2 M.D. R=-5/R=-20
• 9845335 Set of cutter-holders for R=-5/R=-20 cutters
• 9841016 Set of 2 M.D. R=-20
• 9845336 Set of cutter-holders for R:-20 cutters
• 9841017 Set of 2 M.D. R=7
• 9845337 Set of cutter-holders for R:7 cutters
5. GENERAL DESCRIPTION
The FR98H shaper machine is a high-performance elec-
tric tool designed for shaping the edges of longitudinal
beams and crossbeams and modelling coffered ceilings.
Factory-fitted with cutter-holder and straight cutters for
bevel-edging, it also permits rounding or moulding of
shapes by using the moulding cutters included with the
equipment or The optional ones (Fig. 12). If the cutter-
holder is changed, replacing it with the optional one,
then the blades with special profiles can be used (Fig. 12).
The width of the straight or moulded profile obtained
can be set between 0 and 40 mm. The guide runner on
which the piece to be shaped rests can be moved with
respect to the cutter, which means that different profiles
can be made on an edge, according to the zone of the
cutter on which work is being done.
There are two ancillary grips "P" (Fig. 1), one parallel
to the main grip and at the same level, permitting
comfortable work on longitudinal beams and vertical
parts, and a top knob with two optional positions for
work on horizontal surfaces, thus in both cases allowing
a perfectly comfortable and secure two-handed grip
on the machine.