Unit Description; Electrical Characteristics - Ford Connected Charge Station Mode D'emploi

WARNING
- Immediately notify Customer Service if the
charge station, charging cable or the charging
coupling are damaged. Do not continue to use
the charge station.
- Prevent the charging cable and coupling from
coming into contact with external heat sources,
water, dirt, and chemicals.
- Switch off power at the circuit breaker before
installing or cleaning.
- Do not attach extension cables or adapters to
the charging cable.
- Never clean the charge station with a high-pres-
sure cleaner or similar.
- Switch off the power supply before cleaning the
charging sockets.
- The charging cable must not be subjected to
any strain during use.
- You must make sure that no one has access to
the charge station without reading this user
manual first.
- Make sure that the charge station temperature
is within its storage temperature limits when
moving, transporting, or storing it.
- You are strictly prohibited from pulling the
charge station by its cable.
WARNING
When transporting the Ford Connected Charge
Station , handle with care. Do not subject it to
strong force or impact, also do not pull, twist,
tangle, drag, or step on the
Ford Connected Charge Station to prevent dam-
aging it or any of its components.
NOTICE
In addition to the safety instructions in this docu-
ment, also observe further safety instructions in
any other enclosed documents.
6
3

Unit description

This document describes the Ford Connected Charge Sta-
tion. You can find the exact device details on the type label
of the Ford Connected Charge Station.
Electrical SAE
characteristics
Nominal current (A) 48A
(configurable con-
nected load values)
Line voltage (VAC) 240 V (Line-to-line voltage)
(nominal)
Grid frequency (Hz) 60 Hz
(nominal)
Overvoltage cate- II
gory
Protection class
I
Residual current de- See table 4.
vice
Integrated power Accuracy +/- 5%
meter
Connections
Cable feed Mounted on-wall, or in-wall
Connection cross- 2x 6 AWG (L1/L2) 1x 8 AWG (GND)
section (follow local codes/regulations)
(wire dimension)
Charging cable (in- Charging cable with Type 1 coupler ac-
cluding coupler) cording to SAE J1772
Cable length 20 ft / approximately 6
m
Output voltage (V 240 V
AC)
Maximal charging 11 kW
capacity (kW)
Communication &
features
Vehicle–charger SAE J1772
Communication Pro-
tocol (CP)
Authentication Bluetooth (BLE 4.2) – Setup App
SKML9J-10C823-AA
Electrical SAE
characteristics
Display 9 RGB-LEDs
Network interfaces Wi-Fi 802.11n - 150 Mbit/s
Authentication and Bluetooth (BLE 4.2) - Setup-App
mobile communica-
tions
OCPP Version 1.6
Mechanical data
Dimensions (W × H × 10.2 x 17.7 x 5.5 Inches
D)
258 x 450 x 141 mm
Weight (including 17.53 lbs
wall mount bracket
7.95 kg
& charging cable)
Installation height Minimally 35 inches above floor level
(regarding to the bottom of the de-
vice)
Minimally 900 mm above floor level
(regarding to the bottom of the de-
vice)
IP protection class NEMA Type 3S, IP65
Protection against UL2994
mechanical impact
Ambient conditions
Operating tempera- -40°F to +140°F
ture range
-40°C to +60°C
Storage temperature -40°F to +185°F
range (°C)
-40°C to +85°C
Altitude (m) Max. 9,842 ft above sea level
Max. 3,000 m above sea level
Certification com-
patibility
Other standards and ANSI/UL2594:2016 / CAN/CSA C22.2
guidelines No. 280-16
ANSI/UL2231-1:2012 / CAN/CSA C22.2
No. 281.1-12
ANSI/UL2231-2:2012 / CAN/CSA C22.2
No. 281.2-12
FCC Part 15, Subpart B / ICES003
Ford Connected Charge Station Operation manual