Publicité
Les langues disponibles
Les langues disponibles
to 5 min to protect cooking utensils. After the booster is switched off
automatically, the cooking zone continues operation on power level
"9". The booster can be reactivated after some minutes.
In case that the pan is removed from the cooking zone during
boosting, the boosting function remains active and boosting time
continues.
The power management is based on on the principle that the last
entry is requested by the induction as top priority. That means that
previous actions and settings also made for the other cooking zones
are reversed automatically, if necessary.
- If induction identifies the necessity of reducing power at a cooking
zone, the selected cooking stage flashes on that cooking zone
providing a correction period of 3 sec before the power is reduced
automatically to a minimum cooking stage.
- If the setting is adjusted within the correction period, the power
management checks the settings again. Should a new setting lead
to further power reduction, the correction period starts again.
- If no automatic correction needs being made to the cooking zone
setting, the flashing stops immediately and the original value
remains as a steady display indication. Should the situation change
again on the power reduced cooking zone, no automatic power
increase is effected.
Residual heat indicator
It is meant to indicate to the user that the glass ceramic has a
dangerous touch temperature in the circumference of a cooking
zone. The tempera-ture will be determined following a mathematical
model and the remain-ing residual heat will be indicated by means
of "H" on the corresponding zone display.
Heating-up and cooling down will be calculated dependent on:
· the selected setting ("0" to "9")
· the ON/OFF time.
After switching-OFF the cooking zone the respective display shows
"H" until the assigned cooking zone temperature is mathematically
in a uncritical level. (≤ 60°C).
Automatic power OFF function (operating time limitation)
Dependent on the selected setting, every cooking zone will be
switched-OFF after a defined maximum operation time if no
operation of the assigned cooking zone follows within this time
period. Every change of the cooking zone condition (by means of
the PLUS-, MINUS- key) puts back the maximum operation time of
this cooking zone to the initial value of the operating time limitation.
Key lock (child safety feature)
◊ Child safety feature:
Key lock:
After switching-ON the control the child safety feature can be
activated. Press button (5) the key lock function will be activated.
There will be an "Lo" above timer key (6), meaning LOCKED (child
safety feature against unintended switching-ON). The electronic
control remains in a locked condition until it gets unlocked, even if
the control has been switched OFF and ON in the meantime. Also,
a reset of the control (after a voltage drop) does not cancel the key
lock.
Cancelling the key lock:
To unlock and operate the control it is required to Press and hold the
button (8) for 3 seconds, the key lock function will be cancelled. "Lo"
(LOCKED) in the display extinguishes. Audible signal (buzzer)
While the control is in operation the following activities will be
signaled by means of a buzzer:
· normal key activation with a short sound signal.
Timer function (optional)
The timer function is realized in two versions:
· Stand-alone timer 1..99 min: sound signal when the time is over
(= minute minder). This function is only available when the cooktop
is not in operation, i.e. when there is no cooking.
· Cooking zone timer 1..99 min: sound signal when the time is over,
four cooking zones can be programmed independently.
Timer as minute minder (stand-alone):
· If the control is ON and no cooking zone selected, the standalone-
timer can be used by pressing button (6).
· Adjustment range (0-99min), it can be set in 1-minute steps with
MINUS (2) and PLUS (3). Press button (6) to set minutes, after that
press button (6) again to set dozens of minutes.
· Adjustment can be made by tip-operation (with sound signal) After
the timer is set the time runs down according to the adjustment.
When the time is over there is a sound signal and the timer display
blinks.
The sound signal will be stopped
· automatically after 10 sounds Then the blinking of the timer display
stops and the display extinguishes.
Switching-OFF/changing the timer
· The timer can be changed or switched-off anytime by
simultaneously operating MINUS (2) and PLUS (3) keys. (with sound
signal). The timer will be switched off by counting down to "0" with
the minus-key.
For 5 seconds the timer display remains at "0" before it will be
switched-off.
Timer programming on cooking zones
When the control is switched ON, an independent timer can be pro-
grammed for every cooking zone.
· To use the cut off timer, make sure the control is ON, selecting the
cooking zone (4) and the zone LED display blinks, pressing button
(6) and timer display shows "10".
· Adjustment range (0-99min), it can be set in 1-minute steps with
MINUS (2) and PLUS (3). after setting minutes, press button (6)
again to set dozens of minutes. Then wait for 5 seconds the timer
on independent zone is activated.
· During timer programming, a red dot next to pilot light of the
selected cooking zone flashes to indicate the zone is under timer
status.
· When the timer has run down, there is a sound signal and the timer
display shows "--" statically.. The programmed cooking zone will be
cut off and "H" will be displayed if the cooking zone which is hot,
otherwise a stroke will show in the cooking zone display.
· The sound signal and the blinking of the timer LED will be stopped
automatically after 10 sounds and the timer display extinguishes.
· The basic behaviour follows the description of the "minute minder"
(stand-alone-timer).
Pause function (optional)
Pause function is to stop all heating but still keep all the setting you
set, in case your have any interruption when cooking. You can revert
all setting back easily with this function.
To use Pause function
Touch the button (8), all the hearting zones stop working, All the zone
indicators show"||".
Cancel Pause function
Touching the button (8) again, all the heating zones will revert to its
original setting.
NOTE: The function is available when one or multi heating zones
are working.
NOTE: If you don`t cancel the stop Pause mode within 30 minutes, the
induction hob will automatically switch off.
Publicité
